Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely ...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appl...
This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quic...
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete i...
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plasti...
$100.02
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for FFCD2413US4A
Ask our experts a question about this model and we'll get back to you as soon as possible!
19 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jenelle
December 11, 2024
Do you sell a replacement dispenser cap for my Frigidaire dishwasher?
For model number FFCD2413US4A
Hi Janelle, Thank you for writing. The Rinse Aid Cap for this model is listed as PartSelect Number PS421128. Thank you for the inquiry, good luck with the repair!
Will this part stop my dishwasher for leaking at the door bottom?
For model number FFCD2413US4A
Hello Laxton, Thank you for reaching out. Sorry, since you did not provide a part number or description so we can not say what part you are referring to, however we suggest checking the tub gasket and bottom door seal for wear or damage. Thank you for the inquiry, good luck with the repair!
My dishwasher door won't latch but the cycle runs anyway
For model number FFCD2413US4A
Hi Sandy, thank you for reaching out. We have concluded that you may have a damaged door latch, part number PS16218716. You may need to replace the door latch to fix the issue. Glad to be of help!
Door will not stay shut. Inside door does not catch
For model number FFCD2413US4A
Hello Mike Thank you for writing. There must be a faulty Latch PartSelect Number PS16218716 or the complement the Strike PartSelect Number PS12746518. We hope this helps.
My dishwasher has not been getting water thru any cycles. I can tell this, since the tablet is never desolved. I believe the clunking noise I must hear is the tablet bouncing around. There is no white residue inside the dishwasher from any calcium buildup anywhere. Also the round rubber mat at the bottom of the dishwasher is not laying flat and looks ripped in places. I'm hoping I don't have to replace the dishwasher that it can be an easy fix. Thank you.
For model number FFCD2413US4A
Hello Mike, thank you for contacting us. Based on the description that you have provided, we would recommend checking the float switch for continuity. If the float switch is fine, then you may need to replace the water inlet valve, part number PS16218688. It supplies water to the dishwasher. We hope this solves your problem!
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the t
... Read morehing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
