Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
FFAD7033R10 Frigidaire Dehumidifier - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This water bucket assembly is for dehumidifiers.
Water bucket assembly collects condensate water that drips from the evaporator. The assembly may include multiple parts; refer to your parts diagram...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kenneth
June 25, 2021
Fault codes read fo
For model number FFAD7033R10
Hi Kenneth,
Thank you for your question. If you are seeing the F0 error code, it is low on refrigerant as a result of a leak in the refrigerant system. To fix the issue, you will need to remove the remaining refrigerant and fix the leak. Once the leak has been fixed, you can refill it with refrigerant. We hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Melton
January 11, 2020
Black discharge into bucket. How do I disassemble dehumidifier to clean condenser?
For model number FFAD7033R10
Hi Melton. We do not have instructions for this model. However in general you will need to remove the back panel by removing all the screws. Then remove the side panels again by removing the screws securing them, there is tabs locking them in you may need to use some downward force to remove. Then remove the front panel the same way. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Joseph
January 30, 2020
Cleaned coil and now I'm getting "L1" error. Unplugged/waited 30 minutes a few times, but code persists.
For model number FFAD7033R10
Hi Joseph,
Thank you for your question. According to your owner's manual, If the display reads "F1", "F2", "L1" or "H3" error codes, please turn off and unplug the unit, then plug it in again in 30 minutes. If the unit malfunctions again, please contact your authorized Frigidaire service center. We hope this helps. Thank you and have a great day.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Patti
September 13, 2021
It does not take moisture out of air. It is 2 years old, was told by store that we should call the 800 number but cannot get through. Was told by store you will replace it.
For model number FFAD7033R10
Hello Patti, Thank you for contacting PartSelect.com. This would be an issue you need to address with Frigidaire. PartSelect is a online site that sells appliance parts for all major house hold appliances and manufactures. We hope this helps!
Was this helpful?
Thank you for voting!
Stan
June 24, 2022
What does FO mean? Dehumidifier stops. Unplug it. Runs awhile. Then stops.
For model number FFAD7033R10
Hello Stan, thank you for our question. To get rid of the FO, Remove and clean the filter with warm, soapy water. Let the filter dry completely before reinserting it into the dehumidifier. Unplug the unit for 20 minutes and plug it in again to see if the code still appears. This may reset the internal computer and remove the F0 code. We hope this helps
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
