FD791D (BS06) Kawasaki Engine - Overview

This NGK BPR4ES spark plug is sourced from the original manufacturer for use in a variety of small engines. It is responsible for igniting the fuel-air mixture in the engine cylinder, needed for the engine to operate. The spark plug is a small, cylindrical part consisting of a metal body, a ceramic/porcelain insulator, one center electrod...Read moree, and one ground electrode. The spark plug can fail if the insulator breaks, the electrodes wear down, or if it becomes fouled. If the spark plug has failed, you will experience difficulties starting your equipment, decreased power output, and engine misfiring. To check if the spark plug is faulty, you can use a spark tester or a multimeter set to continuity. To replace the spark plug, first disconnect the spark plug wire, and then use a spark plug socket wrench to loosen and remove the old spark plug. Take the new spark plug and set the gap to the correct size. Thread it into the cylinder head using your hands to avoid cross-threading. Once it is in place you can finish tightening it with the spark plug socket wrench. Reconnect the wire, and the equipment should be ready to run smoothly again.

This replacement oil filter is specially designed for use with Kawasaki engines. It is a genuine OEM sourced part, not an aftermarket immitation. This oil filter is used to remove contaminants from the engine oil. This part is manufactured in accordance with applicable EPA emissions regulations. It is recommended to replace oil filters at...Read more least once a season. Please note, this item is sold individually. To replace the oil filter you will need a pipe wrench or a filter wrench. • Disconnect the spark plug • Remove the old oil filter by twisting it counterclockwise • Clean the sealing surface on the oil filter adapter from any dirt or debris • Lightly oil the filter gasket with clean engine oil • Install the new filter

This is an authentic Kawasaki replacement part, sourced from the original manufacturer for use with small engines. The oil seal is used to seat and guide the engines intake and exhaust valves. This item is available as an individual replacement part, please note two oil seals are required.

This is a genuine manufacturer-sourced replacement gasket which is specially designed for use with Kawasaki engines commonly installed on lawn and garden equipment. It provides an air-tight seal for the head, over time seals tend to wear out, become brittle and may crack eventually requiring a replacement. Please note this high-quality part is sold individually.

This is an authentic replacement part manufactured for use with Kawasaki small engines. The flanged hex head bolt is used with several models of engines and has multiple applications. This bolt can be used to secure the fan housing or oil pump cover and is sold as an individual replacement part.

This is an authentic replacement part manufactured for use with Kawasaki small engines. The special gasket is used to form a seal at the connection for the intake manifold. It is recommended to replace gaskets when servicing the engine to ensure proper seals when reassembling the parts. This gasket is available as an individual replacement part, please see model diagram for associative parts.

The pin attaches to the crankcase and is made of metal. This is available as an individual replacement part. This authentic item is supplied directly from the original equipment manufacturer for use with engines, generators, and pumps made by Kawasaki and Toro. A set of pliers may be necessary during the installation of this part. It will need to be replaced if it bends or breaks.

This is an authentic Kawasaki replacement part, sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the insulator and the intake manifold. This intake pipe gasket is available as an individual replacement part, please see model diagram for associative parts.

This is an authentic Kawasaki replacement part, sourced from the original manufacturer for use with small engines. The metal woodruff key is used to link a shaft and rotating gear to allow the gear to rotate with the shaft. This woodruff key is available as an individual replacement part, please see model diagram for associative parts.

This replacement nut is sourced directly from the original equipment manufacturer for use with Kawasaki engines commonly installed on lawn and garden equipment. It is standard hardware which has multiple applications, please refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality hex nut is made of durable metal and is sold individually.