My Orders
FB412-1 DeVilbiss Compressor - Overview
Diagrams for FB412-1
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$14.23
In Stock
Fan Blade
Part #AC-0108
This fan is an exact replacement part for use in air compressors and is sourced directly from the manufacturer. It is made of durable black plastic and is used to cool the compressor during operation. It is not part of a kit or assembly and is sold individually.
This part is located on the end of the motor shaft and will be visibly brok...Read moreen or worn when it needs to be replaced. You will need a screwdriver, a socket set, and a drill to complete this repair.
Customers rate this repair as Easy.
Read less
No Longer Available
ASSY CORD POWER ST
Part #SUDL-413-2
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The three wire cord is encased in a durable jacket and includes terminals at the end of the wires. The cord is used to relay electricity from the outlet to the switch assembly. This item is available as an individual replacement part.
$6.40
In Stock
ORING P/L HEAD
Part #ACG-45
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
Read less
$6.40
In Stock
ASSY FASTENER
Part #ACG-408
This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individu...Read moreally. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.
Read less
$6.40
In Stock
ISOLATOR 3 POINT MOU
Part #ACG-19
No Longer Available
NIPPLE 1/4-18 NPT X
Part #SSP-480
No Longer Available
FILTER INTAKE
Part #DAC-143
This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.
$8.04
In Stock
ORING 2.759/2.719ID
Part #SSG-8156
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
Read less
$6.40
In Stock
SCREW .250-20X.750 U
Part #SSF-586
It is a genuine manufacturer-sourced replacement screw which is specially designed for use with air compressors. This is a standard hardware which has multiple applications depending on the model of your unit, make sure to check appropriate diagrams for the correct location and use of this item. It is a high-quality hex head screw which i...Read mores made of durable metal and it is sold individually, over time the threads may wear out eventually requiring a replacement.
Read less
$12.59
In Stock
NUT .563-18 UNF HEX
Part #SSP-7821-1
This is an authentic replacement part that has been OEM sourced to be used with Porter Cable, DeVilbiss, and Black and Decker air compressors. The metal nut is commonly used to connect the outlet tube to the cylinder head assembly. This item is available as an individual replacement part, a hex wrench is needed for this repair.
$6.40
Special Order
ASSY NUT SLEEVE 3/8
Part #SSP-7813
This is a genuine replacement part manufactured for use with air compressors from DeWalt. This part creates an airtight seal between the elbow and the tube. You may need a wrench to replace this part. This assembly but sleeve is sold individually and made of metal.
$10.32
In Stock
VALVE SAFETY 150 .12
Part #97503734
This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by the...Read more tension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.
Read less
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More