Quick Question!

Have you ever purchased from PartSelect.com before?

Models > F6858W0

F6858W0 Roper Range - Overview

Get Parts and Repair Help for F6858W0

If you know the range repair part you need, you can browse the list of all parts on the F6858W0, or you can search by name or part description. You can also find your part by where it is located on the F6858W0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for F6858W0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$19.19

Lid Switch

This 3 prong lid switch is used for washing machines that do not have a tub light.

Order within the next 25 mins and your part ships today!
$45.94

Round Carborundum Oven Igniter

This round style gas oven igniter, or also known as a broil or bake igniter, has an amperage range between 2.5 and 3.0. It glows white hot to ignite the gas for the oven. The igniter does this by attracting electrical currents through the safety valve to open it. *Please note: this does not replace the flat style igniters. If your gas igniter does not start, glows but does not light, or produces little to no heat when baking, replacing this part could be the solution to your problem. Refer to the diagram provided by the manufacturer for further instructions and guidance.

Order within the next 25 mins and your part ships today!
$2.96

Hex Nut

This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they ar...

Order within the next 25 mins and your part ships today!

DISCONTINUED

SENSOR

DISCONTINUED

SERVICE MOTOR-60 CYCLE (PRODUCTION MOTORS 296086, 295976 OR 295977)

GLASS-D00R

Cushion-Oven Door (3 Req)

DISCONTINUED

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The lower burner would not ignite.

  • Customer: Mark from Rego Park, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 70 of 75 people found this instruction helpful
First I removed the oven racks. Then I loosened the two screws in the back of the oven floor and figured out how to remove it. Then I loosened the two screws at the front of the diverter and, with some pushing and pulling and twisting, was able to get that to come out, too. Then I tried lighting the oven and noticed that the igniter was not glowing. When... read more

Lid closes, switch wouldn't turn on machine.

  • Customer: Kenneth from Wilmington, IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 26 of 37 people found this instruction helpful
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn... read more

Washer would fill up, wash, then stop

  • Customer: Glen from Plano, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 20 of 24 people found this instruction helpful
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on ... read more