Quick Question!

Have you ever purchased from PartSelect.com before?

Models > F4858W3

F4858W3 Roper Range - Overview

Get Parts and Repair Help for F4858W3

If you know the range repair part you need, you can browse the list of all parts on the F4858W3, or you can search by name or part description. You can also find your part by where it is located on the F4858W3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for F4858W3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$31.06

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inches in length, and comes with 2 ceramic wire nuts. Fault temperature sensors are often responsible for F3 and F4 error messages on an electric range. Furthermore, if you find your oven is too hot, will not heat evenly, or simply will not heat at all, there could be an issue with your temperature sensor and you should look to replace it immediately.

$2.96

Cover Screw

Sold individually.

$45.94

Round Carborundum Oven Igniter

This round style gas oven igniter, or also known as a broil or bake igniter, has an amperage range between 2.5 and 3.0. It glows white hot to ignite the gas for the oven. The igniter does this by attracting electrical currents through the safety valve to open it. *Please note: this does not replace the flat style igniters. If your gas igniter does not start, glows but does not light, or produces little to no heat when baking, replacing this part could be the solution to your problem. Refer to the diagram provided by the manufacturer for further instructions and guidance.

$2.96

Screw

This screw is sold individually.

$3.67

Hex Nut

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to wear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.

$22.14

Drip Pan - 8"

Sold individually.

$46.95

Light Blub - Fluorescent - 18 Watt

This light bulb is used in a range's control panel.

$27.50

Rocker Switch - Black

This rocker switch can be used for both the oven selector and/or the oven light.

$5.46

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 143 of 182 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

The lower burner would not ignite.

  • Customer: Mark from Rego Park, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 70 of 75 people found this instruction helpful
First I removed the oven racks. Then I loosened the two screws in the back of the oven floor and figured out how to remove it. Then I loosened the two screws at the front of the diverter and, with some pushing and pulling and twisting, was able to get that to come out, too. Then I tried lighting the oven and noticed that the igniter was not glowing. When... read more

oven sensor quit working

  • Customer: Paul from Modesto, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 45 of 84 people found this instruction helpful
simple part exchange. easy out, easy in. read more