My Orders
F1091QDP2 (ABWPARA) LG Washer - Overview
Diagrams for F1091QDP2
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$24.67
In Stock
Rear Tub Gasket
Part #4036ER2004A
If you notice your washing machine is leaking water from the top of the transmission, it might be due to the gasket being damaged or worn down. When replacing your gasket, consider replacing your tub bearings at the same time. The gasket (or seal) is located at the back of the outer tub of your washing machine. To access this part you wil...Read morel need to pull the top off of the appliance by releasing the screws holding it in place. This part is sold individually, is black in color, and measures 3 inches in diameter.
Read less
$72.00
On Order
Washer Tub Bearing, Rear
Part #4280EN4001F
$72.00
In Stock
Ball Bearing
Part #4280EN4001C
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub sp...Read morein smoothly and to stop the washing machine from shaking during the cycle.
NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.
Read less
$11.77
In Stock
CAP,DRAIN HOSE
Part #5006EN3015A
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cov...Read moreer, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.
Read less
$18.22
In Stock
Shock Absorber Pin
Part #4774EN3002A
This washer shock absorber mounting pin secures the suspension damper to the outer tub and base frame, helping stabilize the wash basket and reduce vibration during operation. By maintaining proper alignment of the shock absorber, it helps prevent excessive movement, banging, shaking, and loud thumping noises during high-speed spin cycles...Read more. Replacing a worn, damaged, bent, or missing mounting pin can restore the effectiveness of the suspension system and help protect other washer components from unnecessary stress and wear. Installation typically involves removing the retaining clip, disconnecting the existing pin from the shock absorber mounting point, inserting the replacement pin, and securing it with the appropriate retaining hardware. For best results, inspect the shock absorbers, retaining clips, and mounting brackets for signs of wear or damage and replace any faulty components at the same time to ensure smooth, stable washer operation.
Read less
$34.74
In Stock
Shock Absorber
Part #4901ER2003A
This is a replacement shock absorber for your washer. The shock absorber is approximately 10 inches long and a little more than one inch wide. It is black and silver in color, and is sold individually. There are four shock absorbers on your washer. They support the tub and prevent it from shaking around. If your washer is shaking or makin...Read moreg a lot of noise during operation, you may need to replace the shock absorber. It is important to determine if you have one or more shock absorbers that need replacement before you begin the repair. This is an OEM part from the manufacturer.
Read less
$18.22
Special Order
Washer Leg Assembly
Part #AFC72909305
This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduc...Read moretion. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.
Read less
$11.77
In Stock
$77.75
In Stock
$11.77
On Order
CLAMP ASSEMBLY
Part #4861EN3003A
$35.80
In Stock
HOSE,PUMP
Part #5214EN3042P
This pump hose carries water between internal components, supporting proper circulation or drainage during operation. Built from durable, flexible materials, it is replaced when leaks, cracks, or restricted flow occur.
$65.73
Special Order
Pressure Switch Assembly
Part #6601ER1006A
Common Symptoms of the F1091QDP2
How this model fails, and the parts that fix it.
Leaking
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More