EX800701AJ Campbell Hausfeld Compressor - Overview

This replacement regulator/manifold manifold assembly is specially manufactured for Campbell Hausfeld air compressors. The manifold kit consists of the manifold, the regulator, two pressure gauges, two quick-disconnects, and the nipple that connects the entire assembly to the air tank. The manifold kit will solve any problems related to a...Read more cracked manifold assembly, as well as any problems with the regulator. To complete this repair job correctly you may need : Phillip's screwdriver, hex drivers, long-nosed pliers, wrenches and heavy-duty wire cutters. • Depressurize the tank • Remove the manifold cover • Remove the pressure hose • Remove the pump assembly from the tank • Remove the manifold • Remove the manifold nipple • Transfer the safety valve • Install the new manifold kit • Secure the the pump assembly • Reinstall the hose • Reattach the manifold cover • Ensure everything is connected and test the compressor

This is a genuine Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The flywheel attaches to the pump's crankshaft and is used to rotate with the belt that is linked to the motor's pulley. This item is priced as a single replacement part.

This Power Cord and Plug Assembly is an OEM sourced part for air compressors. It is wired to the electric motor in order to provide power from a standard outlet. This part is black, consists of a metal wire in a rubber insulated cable, and is sold individually. Depending on how worn it is, your compressor may no longer get power or may ...Read morehave sparks coming from it when it needs to be replaced. If you notice any visible damage such as exposed wires, cracks, or frays, it should be replaced. You will need a screwdriver, pliers, and a wrench to complete this repair. Customers rate this repair as Easy.

Sourced directly from the manufacturer, this plug is an exact replacement part for a variety of air compressors. This part is sold individually, not as part of a kit or assembly. It is gold, made of metal, and will be found on the pressure switch. This part will leak when it has become defective and will need to be replaced if it is dam...Read moreaged or worn. When you install the part, apply Teflon tape to the threads before tightening it in place. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

This is a genuine OEM approved replacement drive belt. It is supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the belt that connects the pump and the electric motor. Over time these rubber belts tend to wear out and stretch eventually requiring replacement to maintain peak performance. Al...Read moreways make sure to clean the pulleys before installing the new belt, this will help to ensure longevity of the new belt. Includes one (1) belt per order. Replacing this belt is a very simple task that should only require a screwdriver. • Make sure to unplug the compressor and drain the tank • Remove the cover screws • Separate the cover from the unit • Remove the old belt • Clean the pulleys • Install the new belt • Secure the cover with the screws

This is original Campbell Hausfeld replacement part manufactured for use with air compressors. The filter is prevents dirt from entering the air intake on the pump. Replacing the filter is part of normal air comrpessor maintenance, please note the filter is sold individually.

This is a genuine Campbell Hausfeld replacement part. The OEM pulley is manufactured for use with air compressors. This pulley connects to the motor's drive shaft and provides a surface that drives belt that links the pump assembly. The pulley can be purchased as an individual replacement part.

This is a genuine Campbell Hausfeld replacement part. The gauge is designed by the manufacturer for use in air compressors. This is a complete assembly made primarily of high-quality plastic and metal, and it is placed in the pressure switch to monitor the pressure within the tank. This part is sold individually.