EX210DM2120 Subaru Engine - Overview

A bowl gasket is designed to create a tight and secure seal between the carburetor bowl and main body of the carburetor, and when it is damaged or not working properly it can cause fuel contamination, loss of engine vacuum and air leakage. This gasket is compatible with various models of engines and is sold as an individual part, without ...Read moreany other hardware. Due to exposure to heat and fuel this gasket can rip, crack and even shrink, leading to fuel leaks as well as other problems for your engine. It is easier to replace this gasket than to maintain it, and you can replace it with a few tools, such as wrenches and screwdrivers. Depending on your model, that process may look different, but ensure the engine is turned off before you disconnect and remove the hardware securing the bowl. Then you carefully lift the bowl off the carburetor, and clean the mating surfaces, after which you replace the gasket and reassemble the carburetor body, ensuring it is all aligned properly and tighten to its manufacturing standard.

This carburetor float bowl, sourced from the original manufacturer, is a cup/bowl-shaped part that receives fuel from the fuel inlet and holds it for use in the engine combustion chamber. It contains a float and needle valve (sold separately) which aid in regulating the fuel levels in the bowl. The bowl itself is made from a high-quality ...Read moreplastic to resist corrosion and can be found underneath the carburetor. If you have noticed fuel leaking from the engine, hard starting, rough idling, and engine flooding, this indicates that the float bowl may be faulty. The bowl can fail due to several reasons, such as general wear from exposure to heat and fuel, contamination from dirt/debris or improper installation. Before you begin your repair, disconnect the fuel lines. Remove the faulty bowl and check that the bowl gasket is still in good condition, if not, you will need to replace the gasket well. Place the new bowl on to the body of the carburetor and secure it with the appropriate fasteners.

This is a Genuine Manufacturer Sourced replacement part used on a variety of Subaru / Robin Engines. This part provides an air tight seal between a Carburetor and an Insulator. This part is made out of Composite Material and it is Sold Individually.

This is an authentic Subaru/Robin replacement part manufactured for use with small engines. The fuel filter fits in the fuel tank just under the cap. This fuel filter strains the fuel as it is poured into the tank. The fuel filter is sold individually.

It is a genuine OEM component which is specially produced for use with a Subaru / Robin engines that are commonly installed on a variety of lawn and garden equipment. This replacement part provides a tight seal for the float chamber body. Unfortunately, over time the material may wear out or get damaged eventually requiring a replacement....Read more Please make sure to check appropriate diagrams of your model for the correct application. It is made of a durable material and is sold individually. You will need a wrench to remove and resecure the bolt that secures it to the float chamber body.

This is an authentic OEM part directly sourced from the Subaru / Robin manufacturer. The plastic packing is compatible with many small engines. This item secures the cup to the cock body-a within the carburetor. This part is sold individually. A screwdriver is helpful in making the repair. Please refer to specific manual and diagrams for instructions.

This is an authentic OEM sourced replacement part used on a variety of Subaru/Robin engines. This part provides an air tight seal between a carburetor and an insulator. This part is made out of composite material and it is sold individually. You would need a wrench to complete a repair.

This item is a genuine Subaru/Robin part that is OEM sourced to ensure quality. The insulator is intended to be used with small engines. The insulator fits between the carburetor and the engine's intake port. The insulator is used to prevent damage to the carburetor that could be caused by engine heat. The insulator is sold as an individual replacement part.

This replacement o-ring is an authentic OEM sourced item that is specially made for use with Subaru/Robin engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and provide an air-tight seal for the carburetor. Over time the material may begin to deteriorate and crack eventually requiring repla...Read morecement to maintain a proper seal. It is made of durable rubber and it is sold individually.

It is a genuine OEM supplied component which is specially produced for use with a Makita generator. This replacement part provides an air-tight seal for the opening in the float body, please make sure to check appropriate diagram of your model for correct application. Over time it may deteriorate and crack eventually requiring replacement...Read more to maintain an air-tight seal. It is made of durable rubber material and it is sold individually.

This fuel union is a genuine manufacturer replacement part that serves as a connection point between the fuel line and the carburetor in outdoor power equipment. It aids in maintaining the proper flow of fuel from the tank by preventing leakages. The fuel union may become unusable if it is damaged or has developed cracks. This can be caus...Read moreed by normal aging, exposure to heat, chemicals, or improper installation. A faulty union will cause fuel to leak through the fuel line causing issues such as hard starting, rough idling, and excessive fuel consumption. To access the fuel union, you will need to first remove the air filter cover, air filter, and carburetor. Next, carefully detach the old fuel union, and thoroughly clean the connecting surfaces to remove any dirt or debris. Position the new fuel union onto the carburetor and reassemble the parts in reverse order to complete the repair.

This genuine manufacturer-sourced component is specially made for use with Subaru / Robin engines commonly installed on lawn and garden equipment. It is the part of the unit that allows a user to turn it on and off. Unfortunately, over time parts will wear out and may begin to fail eventually requiring a replacement. Please make sure to r...Read moreefer to the appropriate diagrams of your model for the correct location and application of this switch. Keep in mind this high-quality plastic body part is sold individually.