EX210D80030 Subaru Engine - Overview

This is an authentic manufacturer sourced replacement part used on Subaru/Robin engines. This part provides an air tight seal for the air cleaner and carburetor. This part is made out of composite material and it is sold individually. You would need a screwdriver to complete a repair.

An oil drain plug is a part designed to facilitate a convenient and controlled method for draining the oil from an engine and is commonly positioned at the lower part of the machine, threaded into the oil sump or pan, offering an easier point for oil removal. This plug is designed for use within various types of small engine equipment and...Read more requires a hex socket wrench to remove and install. This plug is an OEM part that is sold as an individual and prevents any oil from leaking from the oil sump/pan and need only be removed for oil changes. If you notice an oil leak or poorer performance from your equipment, it may be due to an oil leak caused by a broken or loose plug. To replace this plug, ensure you use the torque setting set by the manufacturer of your equipment to properly secure it.

This is a genuine OEM supplied component which is specially made for use with Subaru / Robin engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams for the correct location and applica...Read moretion of this part. Keep in mind this high-quality flange bolt is made of durable metal and is sold individually.

This is a Genuine Manufacturer Sourced replacement part used on a variety of Subaru / Robin Engines. This part provides an air tight seal between a Carburetor and an Insulator. This part is made out of Composite Material and it is Sold Individually.

This OEM flange nut in your engine is a fastener that secures different engine assemblies, like the intake system or the fuel tank. It has a wide, flat base for stability and even load distribution. With a diameter of 6 mm, a thread pitch of 1 mm, and a flange diameter of 13 mm, it is commonly found at assembly attachment points or in are...Read moreas that vibrate. You can tell if a flange nut is broken by checking for bending, cracking, or missing pieces. You may also notice loose assemblies. Not replacing a broken flange nut can lead to issues such as air or fuel leaks and a loss of engine power. To remove a damaged nut, consult your user manual for its location and use a wrench or socket to unthread it. Please note that this flange nut is sold individually, so it is essential to confirm the quantity required for your specific machine. It is also a good idea to keep some extras on hand for future repair needs.

The rocker arm attaches to the rocker pin. This genuine item is supplied by the original equipment manufacturer for use with Subaru and Robin engines. It is made of metal and is sold individually. A socket set might be necessary during the installation of this part. This item will need to be replaced if it breaks.

This gasket, also known as the oil drain plug gasket, is a ring-shaped, metal component used in outdoor power engines. It is supplied by the manufacturer and can be found at the bottom of the engine oil pan where the drain plug is installed. The gasket is responsible for sealing the area between the oil drain plug and the engine block to ...Read moreprevent oil from leaking during oil changes. Over time the gasket can wear down, corrode, or crack. If the gasket can no longer seal the area, oil will escape from the oil pan, leading to inadequate lubrication, increased friction, and engine damage. Before you begin the repair, drain the oil from the engine to prevent contamination. Use a wrench to loosen and remove the oil drain plug. Peel off the old gasket, and thoroughly clean the drain plug and oil pan surface. Install the new gasket and ensure that it sits firmly on the oil pan. Finally, reinstall the drain plug, and be careful to avoid overtightening it.

This is an authentic Subaru/Robin replacement part that has been sourced from the original manufacturer to be used with small engines. The oil seal is used to seal the area around the crankshaft where it exits the crankcase. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

This is an authentic OEM sourced replacement part used on a variety of Subaru/Robin engines. This part provides an air tight seal between a carburetor and an insulator. This part is made out of composite material and it is sold individually. You would need a wrench to complete a repair.

This replacement air filter element is specially manufactured for use on Subaru-Robin engines. It is a genuine OEM item, not an aftermarket alternative. Its purpose is to filter out dust and debris from contaminating the engine. This urethane foam filter is sold individually. Replacing this filter element is a very simple task that does...Read more not require any tools. • Remove the filter cover • Remove the old element • Place the new element in the housing • Secure the cover

This item is a genuine Subaru/Robin part that is OEM sourced to ensure quality. The insulator is intended to be used with small engines. The insulator fits between the carburetor and the engine's intake port. The insulator is used to prevent damage to the carburetor that could be caused by engine heat. The insulator is sold as an individual replacement part.