Quick Question!

Have you ever purchased from PartSelect.com before?

Models > EW30GF65GSG

EW30GF65GSG Electrolux Range - Overview

Get Parts and Repair Help for EW30GF65GSG

If you know the range repair part you need, you can browse the list of all parts on the EW30GF65GSG, or you can search by name or part description. You can also find your part by where it is located on the EW30GF65GSG by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the EW30GF65GSG

[Viewing 6 of 6]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$33.65

PROBE,OVEN TEMP

The temperature sensor measures approximately 9 inches long. It sends the temperature up to the electronic control. Over time this can become weak and might be sending the wrong te...

$8.35

Anti-Tip Kit

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.

$5.35

Steel Washer

This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter ...

$96.24

Bake Igniter

The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.

$9.03

Foot Leveling Leg

Sold Individually. These legs should be adjusted to make your appliance level on uneven flooring.

$8.93

ORIFICE

$6.84

Screw

Sold Individually.

$48.09

RACK

$5.84

Leveling Leg

This part is sold individually. The leveling leg is black in color and measures approximately 2 inches in length. It is made of plastic. The leveling leg is found underneath your r...

$103.74

Pressure Regulator

This valve automatically cuts off the flow of gas at a certain pressure.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't operated. Error code F9

  • Customer: Richard from Centennial, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 35 of 40 people found this instruction helpful
I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws ... read more

anti-tip bracket not installed

  • Customer: Brian from Panama City Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 30 of 38 people found this instruction helpful
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not fi... read more

oven temp not consistent with setting

  • Customer: john from spring, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 50 of 124 people found this instruction helpful
took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking. read more