EW28BS71ISC Electrolux Refrigerator - Instructions

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

problem still persists part did not fix problem. made repairs recommended per your site.

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.