Models > EW27EW65GS3

EW27EW65GS3 Electrolux Wall Oven - Overview

Sections of the EW27EW65GS3

[Viewing 6 of 6]

Manuals & Care Guides for EW27EW65GS3

Click to download
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor – Part Number: 316217002
Temperature Sensor
★★★★★
★★★★★
(14)
PartSelect #: PS820208
Manufacturer #: 316217002
The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut o...
$48.90
  In Stock
Meat Probe Sensor – Part Number: 5304504202
Meat Probe Sensor
★★★★★
★★★★★
(2)
PartSelect #: PS11757868
Manufacturer #: 5304504202
$81.57
  In Stock
Oven Door Light Switch – Part Number: 316445501
Oven Door Light Switch
PartSelect #: PS1146808
Manufacturer #: 316445501
This oven door light switch signals the light to turn off when the oven door closes. If your light switch is defective or you smell a burning odor, make sure to check the switch and replace it. The to...
$71.95
  In Stock
Door Spacer – Part Number: 318165800
Door Spacer
PartSelect #: PS978528
Manufacturer #: 318165800
$18.05
  In Stock
Interior Door Glass – Part Number: 318212200
Interior Door Glass
PartSelect #: PS978631
Manufacturer #: 318212200
$137.12
  Special Order
NUT – Part Number: 316247700
NUT
PartSelect #: PS440161
Manufacturer #: 316247700
This part is made of stainless steel and is approximately half an inch in diameter. This nut is known as a control mounting hex nut. It is metallic in color. This is an OEM part sourced directly from ...
$13.76
  In Stock
Convection Fan Blade – Part Number: 318398302
Convection Fan Blade
PartSelect #: PS3409337
Manufacturer #: 318398302
$25.90
  In Stock
Screw - 8-18 x 1/2 - Black – Part Number: 5304436875
Screw - 8-18 x 1/2 - Black
PartSelect #: PS979383
Manufacturer #: 5304436875
Sold individually.
$11.05
  In Stock
Fan Blade Retainer Nut – Part Number: 316136600
Fan Blade Retainer Nut
PartSelect #: PS439475
Manufacturer #: 316136600
Sold individually.
$15.37
  In Stock
RACK – Part Number: 318365800
RACK
PartSelect #: PS1529560
Manufacturer #: 318365800
$40.41
  Special Order

Questions And Answers for EW27EW65GS3

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the EW27EW65GS3

[Viewing 5 of 5]
Little to no heat when baking
Fixed by
these parts
Show All
Oven is too hot
Fixed by
these parts
Show All
Oven not heating evenly
Fixed by
these parts
Show All
Element will not heat
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating to desired temperature
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Parts Used:
Temperature Sensor
  • Dan from Bellevue, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
140 of 209 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Parts Used:
Convection Fan Blade
  • John from Stevensville, MD
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
13 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not maintain correct set temperature.
Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.
Parts Used:
Temperature Sensor
  • Barbara from RAINBOW CITY, AL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
14 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!