EW140A Honda Generator - Overview

This is an original Honda replacement part that is manufactured for use with small engines. The purpose of the Air Cleaner Element is to filter dirt and debris from entering the engine and clogging it, therefore, comprimising the performance of the engine. Over time the air cleaner element will clog and needs to be replaced. This foam filter is an individually sold part.

This gasket is a genuine OEM replacement part designed to seal the area between the exhaust pipe and cylinder head. It has a length of 3 inches and a width of 1.5 inches. The gasket prevents exhaust gases produced during combustion from escaping through the connection points and prevents air from entering the exhaust system. A faulty gask...Read moreet will result in increased emission of harmful gases, overheating, increased noise, and overall lower engine performance. You will likely need to remove the exhaust pipe to access the gasket. Once the gasket is removed, clean the surface to ensure a good seal and place the new gasket in position. Reconnect the pipe and ensure all parts are secure.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This is an authentic item that is supplied by the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This is an authentic replacement part manufactured for use with Honda small engines. The ignition coil creates and electric charge that is sent to the spark plug that creates an arc to ignite the fuel/air mix in the cylinder. A failing or worn out ignition coil will cause difficulty starting the engine and could lead to a non-start situat...Read moreion, and the ignition coil will need to be replaced. This ignition coil is sold as an individual replacement part.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover

This authentic manufacturer-sourced component is specially designed for Honda engines that are commonly installed on lawn and garden equipment. It is an identical replacement for a missing or a damaged hardware that was installed on a new unit. Make sure to refer to the appropriate diagrams for your specific model for the exact location a...Read morend the correct application of this clip. Keep in mind this high-quality product is made of durable metal and is sold as an individual item.

This is a genuine Honda part sourced directly from the manufacturer for use in engines. The air cleaner wire clip is made of metal. A set of pliers might be helpful during the installation of this item. It may become bent or broken and will need to be replaced. This part is sold individually.

This item is a genuine OEM sourced part that has been manufactured to be used with small engines from Honda. The gasket is used to seal the connection between the carburetor and the insulator plate. It is recommended to replace gaskets when servicing the carburetor to make sure the part connections are sealed and seated correctly when the...Read more parts are reassembled. This item is available as an individual replacement part.