EU6500IS1AT (VIN# EASJ-1200001) Honda Generator - Overview

This is an OEM spark plug designed for engines to ignite the air-fuel mix inside the combustion chamber. This plug is white and silver and made of metal and ceramic materials. Over time the spark plug can become fouled due to a range of reasons including a poor air-to-fuel ratio worn piston rings carbon-build-up and general wear and tear....Read more You can clean a lightly worn spark plug with fine sandpaper and carb cleaner and re-install but generally you are going to have to replace this part often and it is better to replace a fouled plug than try to clean it. If your spark plug is in bad condition you may experience a missed start or a no-start situation. If the engine has 2 or more cylinders you can pull the spark plug wire off to see if the RPMs are dropping due to a miss. On a single cylinder a malfunctioning spark plug is more likely to cause a no-start issue. When replacing the spark plug be sure you torque to the manufacturer specs. Most customers found this repair easy you will just need a spark plug socket.

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is an authentic Honda replacement part, sourced from the original manufacturer for use with small engines. The special hex head bolt is commonly used to secure the ignition module assembly. This flanged bolt is available as an individual replacement part, please see illustrated part list for associative parts.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This rubber fuel strainer cup gasket, found in your garden equipment, distributes pressure and creates a seal between the fuel strainer cup and the carburetor so that fuel does not leak. If it is broken, you will notice fuel leakage or a gas smell, and your engine may sputter or have difficulty starting. Unattended fuel leaks not only was...Read morete fuel but also pose a fire hazard. When removing the gasket, make sure that your machine is shut off and has cooled down. Consult your instruction manual to locate the fuel strainer cup, remove mounting screws and clips with a screwdriver, twist the cup slightly, and lift it away. Peel off the old gasket carefully. It is important to be aware that this authentic OEM replacement part is sold individually.

It is a genuine OEM sourced replacement spark plug which is used with Honda engines commonly installed on lawn and garden equipment. A spark plug is used to deliver electric current from an ignition system to an internal combustion engine. Over time spark plugs tend to wear out, become dirty or fouled eventually requiring a replacement t...Read moreo maintain peak performance. You should gap your spark plug according to the owners manual of the outdoor product you have. This high-quality component is sold individually, please note you would need a spark plug wrench or a socket wrench to install/remove a spark plug.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

It is a genuine manufacturer-approved replacement gasket which is designed for use with Honda engines that are commonly installed on lawn and garden equipment. The purpose fo this part is to create an air-tight seal between the carburetor and the stay assembly, please make sure to check appropriate diagrams of your model for correct locat...Read moreion and use of this item. Over time gaskets tend to deteriorate and crack eventually requiring replacement. It is made of durable composite material and it is sold individually.

This collar is an authentic manufacturer-supplied part which is specially made for Honda engines commonly installed on a variety of lawn and garden equipment. It is an identical replacement for a faulty or a missing hardware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and...Read more the correct application of this component. A wrench set will be needed to secure or remove the hardware that holds this part. This high-quality collar is made of durable metal and is sold as an individual item.

This is an authentic Honda replacement part manufactured for use with small engines. The float valve is used to allow fuel into the carburetor float bowl as it has been drained from the bowl and prevent fuel from entering the bowl when it is full of fuel.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover