EU3000IK1 (A) Honda Generator - Overview

This spark plug creates the spark needed to start compatible small gas engines, it is used in select lawn mowers, generators, snow blowers, and pressure washers, replace a worn or dirty plug if the engine is hard to start, runs rough, or loses power, let the engine cool and remove the plug wire before repair, use the exact engine model number to confirm fit.

This replacement fuel filter is an authentic OEM part that is specially made for use with Honda engines commonly installed on Toro lawn and garden equipment. The purpose of this part is to filter out dirt and other contaminants from fuel that goes into the carburetor. Over time it may get clogged and restrict the fuel flow eventually requiring replacement. Please note this plastic fuel filter is sold individually.

This is an authentic manufacturer sourced replacement part designed for use with Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This is an original part from Honda that is used in a small engine. The key sits in the keyway and keeps the flywheel from free spinning when turned. This part is half mooned shaped and is made of metal. This part is sold as an individual replacement part.

It is a genuine OEM sourced replacement spark plug which is used with Honda engines commonly installed on lawn and garden equipment. A spark plug is used to deliver electric current from an ignition system to an internal combustion engine. Over time spark plugs tend to wear out, become dirty or fouled eventually requiring a replacement t...Read moreo maintain peak performance. You should gap your spark plug according to the owners manual of the outdoor product you have. This high-quality component is sold individually, please note you would need a spark plug wrench or a socket wrench to install/remove a spark plug.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This OEM-manufactured flange bolt provides a secure connection between two parts of your equipment. What is different about a flange bolt is that it has a wide, flat flange at the end. This helps to distribute the load being applied to it and prevents the bolt from becoming loose. Flange bolts are commonly found in lawn equipment, but the...Read moreir location varies by the make and model of the machine. When damaged, the part that the flange bolt was holding may loosen and fall off. You also may observe that it the flange bolt is cracked or corroded. It is important for you to replace broken flange bolts immediately as loose or vibrating parts can detach from your equipment while it is operating. You need a socket wrench to remove a flange bolt, as well as rust dissolver or penetrating oil if it is stuck. This replacement part is sold individually so make sure that you consult your user guide to identify where your flange bolts are and how many your equipment needs.

This is an authentic Honda replacement part sourced from the original manufacturer for use with small engines. The gasket is used to seal the crankcase cover, and it is recommended to replace gaskets when servicing a small engine to ensure proper seals when reassembling the engine. This case cover gasket is available as an individual replacement part.