Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ESL22XGPDBS

ESL22XGPDBS General Electric Refrigerator - Overview

Get Parts and Repair Help for ESL22XGPDBS

If you know the refrigerator repair part you need, you can browse the list of all parts on the ESL22XGPDBS, or you can search by name or part description. You can also find your part by where it is located on the ESL22XGPDBS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ESL22XGPDBS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.31

Temperature Sensor

This temperature sensor, also known as a thermistor, is used for refrigerators and freezers. The sensor sends the temperature reading of the refrigerator towards the control board....

$35.96

Ice Bucket Auger

When activated, the auger rotates and pushes ice out of the bin through the chute to the user.

$13.20

Defrost Thermostat

This defrost termination thermostat acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. The the...

$56.41

Dual Inlet Water Valve

This double outlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

$21.46

Drawer Slide Rail - Right Side

The drawer slide rail for the right side is used for refrigerators. The drawer slide rail attaches horizontally to the refrigerator wall and supports the drawer so it can easily sl...

$65.78

Ice and Water Filter

This is an ice and water filter. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. This will also ensure a normal dispensing rate. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See Related Parts. Sold individually.

$19.42

Drawer Slide Rail - Left Side

When looking inside the fridge, this white drawer slide rail is located on the left side of the refrigerator. Rail ONLY.

$7.53

Dispenser Door Assembly or Flapper

The dispenser door assembly (or flapper) is what opens to release the ice once the lever has been pressed. This part mounts in the ice dispenser. The cranker no longer comes with this part. You can use the original crank. The crank is sold separately depending on the model number of the appliance. For this repair, all you will need is a Phillips screw driver and a small flat blade. Disconnect the power, remove the escutcheon from around the dispenser, lift up the control panel, disconnect all wire connectors, use a screwdriver to remove all four screws of the housing, and lift the housing out. You will now see the flapper: push the tabs that are securing it in place to remove the piece, install the new flapper by lining it up and snapping into place.

$159.28

Ice Maker

This is a replacement ice maker kit, it is used in the freezer section of your refrigerator. This particular model will produce seven round or crescent shaped cubes every cycle. Th...

$41.11

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigertor water dispenser not working BUT ice machine is working

  • Customer: ralph from bristow, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 941 of 1024 people found this instruction helpful
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and pr... read more

Plastic Auger blades broke in ice tray

  • Customer: Tim from Newport News, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 544 of 572 people found this instruction helpful
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with sm... read more

Ice box and freezer would not get cold,the back wall of the freezer was covered with ice

  • Customer: Greg from Aledo, TX
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 545 of 585 people found this instruction helpful
1. I had to defrost the ice off of the back wall of the freezer with a blowdryer.
2. Removed the four 1/4'' screws and removed the back panel.
3. Defrosted all of the ice off the coils and heater.
4. I replaced the defrost thermostat and heater by following the directions that came with them. The directions are very clear and easy to follow. I... read more