EIMGD60LSS2 Electrolux Dryer Parts & Repair Help | PartSelect
Models > EIMGD60LSS2

EIMGD60LSS2 Electrolux Dryer - Overview

Manuals & Care Guides for EIMGD60LSS2

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(22)
PartSelect #:PS470049
Manufacturer #:5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes...
$29.76
In Stock
Order within the next 3 hrs and your part ships today!
PartSelect #:PS425733
Manufacturer #:216396900
This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to t...
$15.76
In Stock
Order within the next 3 hrs and your part ships today!
PartSelect #:PS417463
Manufacturer #:131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, int...
$11.66
In Stock
Order within the next 3 hrs and your part ships today!
PartSelect #:PS417085
Manufacturer #:131168200
Sold individually.
$9.68
In Stock
Order within the next 3 hrs and your part ships today!
(4)
PartSelect #:PS459818
Manufacturer #:5303281135
This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer i...
$48.51
In Stock
Order within the next 3 hrs and your part ships today!
(18)
PartSelect #:PS2349312
Manufacturer #:134793600
Located at the front of the washing machine, this dryer lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 14 in...
$57.67
On Order
(5)
PartSelect #:PS7783961
Manufacturer #:137539200
$25.39
In Stock
Order within the next 3 hrs and your part ships today!
(2)
PartSelect #:PS2349303
Manufacturer #:134786100
$50.99
In Stock
Order within the next 3 hrs and your part ships today!
PartSelect #:PS2349290
Manufacturer #:134715900
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotat...
No Longer Available
PartSelect #:PS428074
Manufacturer #:218470300
This valve is intended for use with the ice maker in a refrigerator. The water valve supplies the water needed to make ice, so if your ice maker is not making ice or dispensing wat...
$50.77
In Stock
Order within the next 3 hrs and your part ships today!
Questions and Answers for EIMGD60LSS2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would heat initially then cool down

  • Customer: Brett from Monticello, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 90 of 101 people found this instruction helpful
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible... read more

Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.

  • Customer: Bruce from Burnsville, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 40 of 46 people found this instruction helpful
1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, installed new coils and bra... read more

No heat, but everything else works. Ran continuity tests on everything and found gas valve solenoid coils open.

  • Customer: Barry from Fremont, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 25 of 29 people found this instruction helpful
Just as others described in your forum, getting to the gas valve solenoid coils is relatively easy. Pop the top lid and lay it back, remove 2 inside screws that fasten the front cover and pull back off the snap clips and lift up and off. Remove 3 screws that hold the entire gas control assembly to the bottom of the dryer and remove. Unfasten 2 screws on ... read more