EIMED55IIW3 Electrolux Dryer Parts & Repair Help | PartSelect
Models > EIMED55IIW3

EIMED55IIW3 Electrolux Dryer - Overview

Manuals & Care Guides for EIMED55IIW3

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
PartSelect #:PS446428
Manufacturer #:3204267
This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will c...
In Stock
PartSelect #:PS425733
Manufacturer #:216396900
This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to t...
In Stock
PartSelect #:PS417463
Manufacturer #:131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, int...
In Stock
PartSelect #:PS417085
Manufacturer #:131168200
Sold individually.
In Stock
PartSelect #:PS2349303
Manufacturer #:134786100
In Stock
PartSelect #:PS2349395
Manufacturer #:137032600
In Stock
PartSelect #:PS2349290
Manufacturer #:134715900
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotat...
No Longer Available
PartSelect #:PS4704883
Manufacturer #:134711401
On Order
PartSelect #:PS3495292
Manufacturer #:137380600
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold i...
In Stock
PartSelect #:PS418263
Manufacturer #:131601000
In Stock
Questions and Answers for EIMED55IIW3
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Noisy Dryer

  • Customer: Philip from Oakland, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 13 of 15 people found this instruction helpful
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replacea... read more

The clip broke off our sensor making it disconnect, thus we had in inoperable 'new' machine.

Moisture Sensor – Part Number: 134786100
  • Customer: Stacey from TWO RIVERS, WI
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton! read more

Internal vent inside the drum was coated in black (plastics from use)

Air Duct – Part Number: 5304508449
  • Customer: Rich from New Albany, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
1. Loosened the 3 screws inside of the drum
2. Removed the entire back of the dryer (lots of screws)
3. Removed the old vent (there are 2 screws at the bottom that hold it in)
4. Install new vent (put the screws back in)
5. Close up back and proceed to put all of the screws back read more