This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
The door strike is used in washers and is attached to the door to activate the switch when the door is closed. This ensures that the washer door remains locked and closed. If your door does not stay o...
This is a bellow, though it may also be known as a door boot seal, and it is a part for your washing machine. The function of the bellow is to prevent leaks by forming a seal in between the wash tub a...
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ed
July 23, 2021
I have an elflw55hiow (Electrolux) the cycle selector is not working properly. It takes several attempts to get the correct wash cycle you want. What part do i need to fix it?
For model number EIFLW55HIW0
Hi Ed,
Thank you for your question. If the cycle selector is not working, you will need to replace either the knob or possibly the electronic control board. The part number listed under your model number for the electronic control board is 134994900 and the part number for the knob is 134766500. The knob has been discontinued and you will need to contact Frigidaire for information on a replacement part. If you would like to place an order for the electronic control board, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
Washer won't spin fast to get the water out, sometimes it does and make very loud banging noise. Any ideas what it could be? Thank you.
For model number EIFLW55HIW0
Hello Jeff, Thank you for the question. This could indicate the Belt is worn and slipping. We also suggest checking the Idler Pulley for damage or wear. We hope this helps!
My soap dispenser drawer won’t stay closed keeps popping open
For model number EIFLW55HIW0
Hello Janet, thank you for contacting us. We would recommend checking the drawer conveyor, part number PS2350419. If this does not help, the issue is probably related to the drawer assembly, part number PS3495314. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
Removed old drawer and replaced it with new one. This is the second drawer assembly I have purchased in 6 months. This piece of junk must be a cash cow for Electrolux. If they would make the small latch out of metal instead of plastic, there would be no problem. But that might cost an additional $ .007 per washer. On the positive side, partselect.com had the part and delivered it promptly.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
