If you are having trouble cleaning out your grease filter, or if it is damaged to the point of no return, maybe it is time to replace it. The grease filter is a ventilator that traps grease from the exhaust air. The dimensions of this part are roughly 6 inches wide, by 8 inches deep, and this specific model is silver. Replacing this part ...Read moreis an easy fix as it will snap in and out of place, with no tools required. This part is sold individually.
The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capa...Read morecitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..
The tray, used in a microwave, holds food plates and containers on it. The tray, also known as a turntable, rotates when the microwave is heating up food to ensure the plate of food is evenly heated. If your glass tray is broken, shattered, or is not rotating when heating, it is best to replace it for better heating results. The tray has ...Read moredimensions of 33 x 35.6 x 2.5 cm and weighs 455 grams. Refer to the manual provided by the manufacturer for installation instructions and guidance.
This is a lower handle end cap for a microwave door. It covers the end of the microwave door handle. The cap measures approximately 2 inches by 2.5 inches and is stainless steel. It is located at the lower end of the door handle. This is an authentic OEM replacement part. It is recommended to get a technician to replace this part because ...Read moreyour microwave door contains shielding components. Replacing this part on your own may cause leaks in the door. Your microwave should be tested for leaks in the microwave shield to ensure safe operating of your appliance.
This part is an upper handle end cap and it works in conjunction with your microwave. The purpose of this end cap is to clip into the microwave to cover the end of the door handle. This part is made of stainless steel, and it measures to be roughly 3 inches long, 2 inches high, and 1 inch wide. For safety purposes, we ask that before maki...Read moreng this repair you unplug your appliance and let it sit for a while unused. Your microwave capacitator stores electricity in large quantities even after it has been unplugged. We recommend using work gloves for this repair.
The roller guide sits underneath the glass turntable tray in your microwave. If your microwave turntable tray is not rotating properly, you may need to replace the turntable roller guide. The function of this part is to house the glass plate, and rotate to cook food evenly. This part has a round piece in the middle, approximately 2 inches...Read more in diameter, and 3 arms which are approximately 4 inches in length each. Each arm has a small plastic wheel on the end that supports the glass turntable tray. This part is an OEM part sourced directly from the manufacturer, and is sold individually.
This mounting bracket is used to mount microwaves to the wall when installing the unit over a range. This metal, genuine OEM mounting bracket is approximately 31 inches long x 2 inches wide. If you notice that your wall mounted microwave is pulling away from the wall, take it down immediately and check the mounting bracket and the screws ...Read moreused to fasten the bracket to the wall. If you notice any damage to the wall mounting bracket, look to replace it right away to avoid further damage to your wall, or to the microwave. The hardware to perform the installation for this part is sold separately.
The microwave door latch spring creates tension, and engages the door latch when the door is closed. This spring is made completely of metal, and is approximately 1 inch long. If your microwave door will not open or close properly, the microwave will not start. You may need to remove the control panel to gain better access to where the sp...Read morering attaches, so make sure the power is disconnected from the microwave. This part is sold individually.
NOTE: Remember to discharge the capacitor for your microwave before beginning this repair. The capacitor can hold a potentially lethal charge even when the power has been disconnected from the microwave itself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Timer would run but the microwave won't start
91 of 149 peoplefound this instruction helpful.
Tim from Chicago, IL
Easy
30 - 60 mins
Screw drivers
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.
Was this helpful?
Thank you for voting!
microwave wouldn't turn on but timer worked.
35 of 64 peoplefound this instruction helpful.
Steve from Moorhead, MN
Easy
Less than 15 mins
Pliers, Screw drivers
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a
... Read more 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .
Read less
Was this helpful?
Thank you for voting!
Microwave would count down but not run
29 of 49 peoplefound this instruction helpful.
Betty from Kimball, TN
Easy
15 - 30 mins
Pliers, Screw drivers
After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the
... Read morebad switch with the new one and replace all the wires. Reassemble the unit and you are good to go.