The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capa...Read morecitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..
We understand how important it is for your appliances to work reliably and safely. When it comes to your GE appliances, our GE Door Switch Assembly is just what you need. This switch assembly is much more than a spare part. It provides a vital function by ensuring that your appliance door closes securely, while also working to communicat...Read moree its state to your device. This not only ensures you can operate your appliance with confidence, but it also significantly enhances your appliance's safety and reliability. What's special about this switch assembly is its quality - you can trust that this part won?t let you down. It's been carefully engineered with top-rated precision to replace any worn out or broken door switch on your GE appliance. If you're on the search for a fix to get your appliance working like new, this is it. The GE Door Switch Assembly not only boosts your device's performance, but it can also prolong its lifespan thanks to its outstanding quality. An easy replacement and an even easier decision to make for the longevity and reliability of your appliances.
This door release lever, also known as a door open lever, is an original manufacturer replacement for microwave/oven combos. When the door release button is pressed, the lever releases the door latch, allowing the door to open. The lever can fail due to physical damage or wear over time, making it difficult or impossible to open the micro...Read morewave door. You will need to remove the microwave cover/housing to access the lever. First, unplug the microwave from the power source to prevent electrical hazards. Locate the control panel and remove the fasteners that hold it to the microwave frame. Make a note of how the wires are connected to the terminals on the control board. It can be helpful to take a picture for reference. Pry the door release lever off and press the new one into place on the control panel. Reposition the control panel on the microwave frame and reattach the wire connectors to the appropriate terminals. Make sure it is properly aligned before mounting it in place with the fasteners. Reassemble the microwave and reconnect it to the power source.
This microwave waveguide cover is a protective mica panel that shields the internal components of the microwave—especially the magnetron—from moisture, grease, and food splatter during cooking. It helps prevent sparking and keeps the appliance operating safely and efficiently while still allowing microwaves to pass through to heat food. M...Read moreade from heat-resistant mica material, it should be replaced if it becomes burned, cracked, or stained. Installation is simple and usually involves sliding the old cover out and securing the new one in place to restore safe operation.
The roller guide sits underneath the glass turntable tray in your microwave. If your microwave turntable tray is not rotating properly, you may need to replace the turntable roller guide. The function of this part is to house the glass plate, and rotate to cook food evenly. This part has a round piece in the middle, approximately 2 inches...Read more in diameter, and 3 arms which are approximately 4 inches in length each. Each arm has a small plastic wheel on the end that supports the glass turntable tray. This part is an OEM part sourced directly from the manufacturer, and is sold individually.
The microwave door latch spring creates tension, and engages the door latch when the door is closed. This spring is made completely of metal, and is approximately 1 inch long. If your microwave door will not open or close properly, the microwave will not start. You may need to remove the control panel to gain better access to where the sp...Read morering attaches, so make sure the power is disconnected from the microwave. This part is sold individually.
NOTE: Remember to discharge the capacitor for your microwave before beginning this repair. The capacitor can hold a potentially lethal charge even when the power has been disconnected from the microwave itself.
Introducing the SWITCH KIT, a genuine OEM component from Frigidaire. This kit, including a Monitor Switch with ceramic, is an integral part of your microwave's functionality. Not just any part, this door interlock switch comes with a fuse to ensure safety by preventing the appliance from working if the door interlocks fail. However, given...Read more the potential risks associated with high-voltage capacitors in a microwave retaining lethal electrical charges even when unplugged, it is advised that installation be performed by a service technician. This essential item is specifically designed for select models of Frigidaire microwaves. Please ensure your model is compatible with this part, as there may be slight variations in size and shape.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Timer would run but the microwave won't start
91 of 149 peoplefound this instruction helpful.
Tim from Chicago, IL
Easy
30 - 60 mins
Screw drivers
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.
Was this helpful?
Thank you for voting!
microwave wouldn't turn on but timer worked.
35 of 64 peoplefound this instruction helpful.
Steve from Moorhead, MN
Easy
Less than 15 mins
Pliers, Screw drivers
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a
... Read more 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .
Read less
Was this helpful?
Thank you for voting!
Microwave would count down but not run
29 of 49 peoplefound this instruction helpful.
Betty from Kimball, TN
Easy
15 - 30 mins
Pliers, Screw drivers
After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the
... Read morebad switch with the new one and replace all the wires. Reassemble the unit and you are good to go.