Models
>
EI30BM6CPSC
EI30BM6CPSC Frigidaire Microwave - Overview
Sections of the EI30BM6CPSC
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
FUSE
PartSelect #: PS12071294
Manufacturer #: 5304509451
This fuse, also known as a cartridge fuse, is a genuine OEM replacement part for microwaves. It has a glass cylindrical body with a metal cap on each end. The cap connects the fuse to the circuit. If ...
$13.12
In Stock
Wave Guide Cover
PartSelect #: PS12071278
Manufacturer #: 5304509435
This OEM waveguide cover in your microwave is a heat-resistant component that prevents food, grease, and moisture from entering the waveguide. It is typically located on the side or top wall of the co...
$14.88
In Stock
Door Switch
PartSelect #: PS12071302
Manufacturer #: 5304509459
This door switch is designed for use with various makes and models of microwaves and is a genuine OEM part. This individually sold switch connects to the frame of the microwave through the door switch...
$52.03
In Stock
PLATE
PartSelect #: PS12071322
Manufacturer #: 5304509487
Hardware is not included. Must be ordered separately.
$56.10
In Stock
PUREAIR MICROWAVE F
PartSelect #: PS12366452
Manufacturer #: OTRFILTER
This is an authentic charcoal filter, which works with microwaves.
$28.16
In Stock
DAMPER
PartSelect #: PS12071321
Manufacturer #: 5304509486
This is an OEM vent damper, which works with microwaves.
$27.51
In Stock
Questions And Answers for EI30BM6CPSC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the EI30BM6CPSC
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Power would not come on, would trip breaker when connected.
First thing I dir was search YouTube for any related videos and found this one https://www.youtube.com/watch?v=uHj4H9Fdxrc, it was the exact problem my microwave was exhibiting. Once I verified the problem by troubleshooting, I removed the part and verified that the switches were working fine, the door latch assembly showed signs of wear
... Read more
which was the cause of the problem. After receiving the replacement part I installed it, verified that power was restored to the unit and reassembled the microwave, works fine, hope it lasts a long time!
Read less
Parts Used:
-
JOSEPH from MIAMI, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cover needs replacing
You have to be very careful because the wave guide cover is very brittle. It needs to be bent very gently in order to fit the four ends into each slot. I would highly recommend buying two just in case the first one breaks.
Parts Used:
-
Christopher from CARY, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch failed to latch
made TWO (2) parts orders one (1) for latch, (1) for the Spring. Using a dinner knife I removed plastic cover on inside door to inspect the spring and latch. Found both to be in working order, where the spring attached at the lower plastic spring attachment area was broken. In other words I needed another door or Microwave unit, After ex
... Read more
anining area I determined that a home fix was possable with 1/16 inch diam. piano wire by bending a tight loop at top and hooked to spring, then pulling down to put tention on spring enough to keep latch in proper possion, I then marked wire and cut it and bent it in a hook and hooked it to a metal fin like brace, operated door works well. TOO MANY PLASTIC PARTS.
Read less
Parts Used:
-
Larry from Junction City, OR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!