A carburetor controls how much fuel and air reach a portable generators engine. Varnish, corrosion, a sticking float, or a worn needle can make the engine hunt, run unevenly, stop under load, or refuse to start. A complete replacement assembly may be useful when cleaning and basic service do not correct the fault. Compare the mounting pat...Read moretern, throttle and choke linkages, fuel connection, and full engine code before ordering. New mounting gaskets may need to be purchased separately. Shut off the fuel, disconnect the battery and spark plug, and label every connection. After installation, check for leaks and confirm stable speed and output under the recommended test load.
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Generac portable generators. The bolt helps to secure the cover. This is a high-quality replacement for a missing or a damaged hardware that was originally installed on a new unit. Please make sure to check the appropriate diagrams of your...Read more model for the correct location and application of this part. Keep in mind this high-quality cover bolt is made of durable metal and is sold individually. A wrench will be needed to secure or remove it.
This is an OEM replacement part sourced from the Generac manufacturer. The metal push rod 174.9 is designed for use with portable generators. This item is secured into the assembly, cylinder head seats and guides. The push rod opens and closes the generator valves. This part is sold individually. A screwdriver is needed to make the proper repair.
This is an original Generac replacement part manufactured for use with portable generators. The foam pre-filter traps dirt along with the main air filter to prevent contamination inside the engine. The filter can be cleaned but eventually will need to be replaced as part of normal maintenance. This air filter pre-cleaner is sold individually.
It is a genuine item that is supplied directly by the original equipment manufacturer for Generac portable generators. The cam actuates rocker arms that press down on the valves, opening them. This is a high-quality replacement for a missing or a damaged rocker arm that was originally installed on a new unit. Please make sure to check the...Read more appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality rocker arm is made of durable metal and is sold individually. A wrench set will be needed to take the engine apart when performing this repair.
This recoil starter is an original replacement part manufactured for use with Generac portable generators. The recoil starter is used to manually start the engine, by engaging the flywheel when the rope is pulled. The part includes the recoil pulley, spring, rope, handle, and recoil cup. The recoil starter is sold individually, please see model diagram for additional parts.
This authentic manufacturer-sourced component is constructed of flexible plastic, and is made for use with several portable generators. The breather hose (gh410 engines) is secured onto the crankcase, providing a pathway for air to circulate in the engine. This item is sold individually. A wrench and a screwdriver are necessary for the removal and replacement.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Carberator gummed up from sitting in storage. Fuel gone bad in the tank
6 of 7 peoplefound this instruction helpful.
Robert from BATON ROUGE, LA
Really Easy
30 - 60 mins
Nutdriver, Pliers, Socket set
With a 12-in-one nut screwdriver I removed the two bolts holding the breather cover and air filter. Then I used about a 9/16 deep socket ratchet to remove the nuts holding the breather housing to the carburetor assembly studs. A pair of needle nose pliers was used to disconnect the throttle then I wriggled the breather cover away from t
... Read morehe carburetor so I could get to the fuel line. I managed to pull the fuel line off the carburetor and from the shut-off valve at the tank. The carburetor slid freely and easily off the carburetor studs and I was careful not to damage the carburetor gasket since none came with the new carburetor. I used a single edge razor blade to free the gasket from the old carburetor. A very small amount of silicone lube was used on the gasket and then I sandwiched the old gasket between the carburetor intake and the new carburetor and attached the throttle connection. Before beginning the reassembly I unscrewed the shut-off valve from the tank and used a funnel to drain the very old fuel into a 5-gallon bucket. I made sure the valve was clean by spraying carburetor cleaner through it and did the same with the old fuel line, making sure everything was clear of any obstruction. Then replace the breather assembly back over the carburetor studs, snugged the nuts back on and then replaced the air filter and cover. I re-attached the fuel line to the fuel valve and the carburetor, added a half gallon of clean fresh fuel and was ready for a smoke check. Pulled the starter rope three times with the choke full on, then turned to half-choke and the puppy started right off. I then turned the choke completely off and the engined purred along. I then exercised the generator by plugging in and running a number of power tools for about 15 minutes. Followed standard shut off procedures and the generator is ready for use. Saving the old carburetor to be cleaned and held on reserve for the future. Might want to have another gasket handy or some gasket material should it have to be replaced in the future.