This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This part is both the start relay and the overload. The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed and the overload provides extra protection against excessive temperatures.
This basket provides organized storage and easy access during appliance operation. Sturdy construction supports regular use without sagging or shifting. Replacing a damaged basket restores capacity, stability, and convenience.
This gasket seals the door to prevent leaks and maintain temperature. Replace if gaps or wear appear. This part is designed to keep your appliance operating reliably and efficiently. Replacing a worn or failing component helps prevent further issues and can extend the overall lifespan of your unit.
This part maintains the proper temperature. When the refrigerator reaches the desired temperature, this part interrupts the flow of electricity to the compressor which stops the cooling process.
This is the mechanics (motor/engine) of the cooling system. It kicks in whenever the thermostat demands cooling. ***NOTE: This part needs to be installed by a trained professional in appliance repair. It requires special tools and knowledge to do so.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Our Refrigerator and freezer stopped working
60 of 71 peoplefound this instruction helpful.
Anna from Lincoln, RI
Easy
Less than 15 mins
Screw drivers
I had read on a fix it site that the start device for the compressor on this particular model was known to fail after 3-5 years. When we received the part it looked like something that just plugged into the compressor. My husband unscrewed the panel in the back of the fridge and saw the part on the compressor. He first removed the thre
... Read moree wires that it was connected to, and the wires were inside a plug so all he had to do was remove the plug from the start device. He then removed the old start device from the compressor. Plugged in the wire plug into the new start device, and pushed in the new start device into the compressor. There was also another black part plugged into the old start device that he plugged inot the new start device that connected to the compressor. Our freezer and refrigerator starting working. Within a couple of hours our freezer had made ice.
Read less
Was this helpful?
Thank you for voting!
Refrigerator not cooling, water dripping from doors
21 of 24 peoplefound this instruction helpful.
Darrell from Hammond, LA
Easy
15 - 30 mins
Screw drivers
Water was dripping out of top freezer door and had water under the refridgerator. I could hear a clicking noice from bottom of refrigerator every 3-5 minutes. After removing back panel, I noticed the fan was running and the clicking seemed to be coming from somewhere around the compressor which was warm. I noticed on the site a si
... Read moremular problem had been submitted. It said to remove the start relay and if it rattled it was bad. I removed two wires from it ( it is connected onto the side of the compressor) then took a small screw driver to pry it away from the compressor. It not only rattled but had tiny pieces falling out. I ordered the part and replaced it in less than 15 minutes total and all is well.
Read less
Was this helpful?
Thank you for voting!
stopped cooling,the compressor would come on and shut back off.
16 of 19 peoplefound this instruction helpful.
william from shady dale, GA
Easy
15 - 30 mins
Screw drivers
pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the loc
... Read moreal appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.