EG1400ZA Honda Generator - Overview

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is an authentic manufacturer sourced replacement part designed for use with small Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the bowl. Over time gaskets tend to deteriorate and would need to be replaced. This set includes two (2) rubber material gaskets. You would need a wrench set to complete this repair.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This item is an authentic OEM part which is made for use with Honda engines commonly installed on a variety of lawn and garden equipment. The clip is utilized to secure the fuel tube. If the clip is damaged or is missing, this will provide an identical replacement for a missing or a damaged component that was installed on a new unit. Chec...Read morek the diagrams of your model for the exact location and the correct application of this hardware. One durable metal clip is included. You may need pliers to secure and remove it.

This is an original replacement part manufactured for use with Honda small engines. The starter rope is pulled to engage the flywheel to start the engine, and the rope recoils back into the starter when the rope is released. The starter rope is sold individually, please see model diagram for associative parts.

This is an authentic item that is supplied by the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

It is an identical replacement for a missing or a faulty item that is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. This is a replacement cap-fuel with a metal mesh filter on top, it will help to catch any large contaminants from the fuel. Please make...Read more sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.

The fuel hose attaches to the tube clip and the fuel filter. This part is available individually. It is a genuine OEM sourced part which is specifically designed for use with Honda and Toro engines. You may need a set of pliers when replacing this part. This item is made out of rubber and will need to be replaced if it breaks.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

It is an authentic OEM sourced replacement filter which is specially produced for use with Honda engines commonly installed on lawn and garden equipment. The purpose of this component is to ensure that the fuel supplied to the unit is free of dust and other harmful components, over time it may get clogged eventually requiring a replacemen...Read moret. It is a durable part which is made of high-quality plastic material and it is sold individually.

This is a ball bearing that is used to reduce friction between the crankshaft and crankcase cover within various small engines. This bearing is sold as a singular part from its original equipment manufacturer and is made of high-quality metal. Featuring a 2.05-inch (52mm) outer diameter and a .98-inch (25mm) inner-diameter, this bearing p...Read morerevents excessive noise, rattling, wobbling and vibrations from interfering with the crankshaft and crankcase as a whole. If you notice any of those things, you need to inspect this bearing for damage or wear immediately to prevent further damage to any other internal components. Replacing this bearing will require you to use a screwdriver and wrench to gain access to the internal portion of the engine for equipment. First, disconnect the spark plug and make sure to adhere to any equipment manufacturer assembly instructions, such as removing the engine cover, ignition coil and carburetor. Once you have access to the bearing location, remove it and ensure the entire area is cleaned and lubricated adequately before installing the new bearing and aligning the crankshaft. After that is complete, you can carefully reassemble the motor.

This is an authentic Honda replacement part that has been sourced from the original manufacturer to be used with small engines. The metal wingnut is used to fasten the bolt that secures the air cleaner housing. This item may not require tools to install and is priced as a single item.