Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ECKMF94

ECKMF94 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for ECKMF94

If you know the ice maker repair part you need, you can browse the list of all parts on the ECKMF94, or you can search by name or part description. You can also find your part by where it is located on the ECKMF94 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for ECKMF94 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term

[Viewing 1 of 1]
$84.92

Icemaker

This part number matches the current model number "ECKMF94".

This genuine OEM ice maker kit is designed to fit refrigerators that did not originally come with an ice maker. This kit contains everything needed to install the new ice maker on your refrigerator including: the ice maker, ice bin, inlet valve, fill tube, and hardware. If your new ice maker does not function properly after being installed, check the freezer temperature. The freezer must to be around zero degrees Fahrenheit. Remember to disconnect the power and water supply to your refrigerator before beginning this installation. Make sure to check that your model is compatible with this part before ordering. Note: The manufacturer has updated this part. It may differ in appearance but will function the same as the original.

Sections of the ECKMF94

[Viewing 1 of 1]

Manuals & Care Guides for ECKMF94

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$65.25

Icemaker Control Assembly

The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It...

$5.21

Icemaker Water Fill Tube Kit

The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaking, you may need to replace the water fill tube. This water fill tube kit comes with a fill tube and a compression nut. This part is made of white plastic and is approximately 10 inches in length. The ice maker water fill tube is in the rear of the fridge. To complete this repair, you will need a 1/4 inch nut driver and a utility knife. Before beginning this repair, you may want to disconnect the water and power supply to the refrigerator.

$84.92

Icemaker

This genuine OEM ice maker kit is designed to fit refrigerators that did not originally come with an ice maker. This kit contains everything needed to install the new ice maker on ...

$66.36

Single Water Inlet Valve - 120V 60Hz 35W

The single water inlet valve, also known as a water solenoid valve, is used for refrigerators. This part is a solenoid-operated switch that releases water from the supply line to the water valve and into the icemaker mold when activated. If your icemaker is making small cubes, does not dispense ice or water, or leaks, this replacement could solve the issue. The tools needed for this repair are a 1/4 inch nut driver and a utility knife. Refer to the diagram provided by the manufacturer for further instructions. As a safety precaution, remember to unplug your dryer from the power source.

$2.96

Screw

Sold individually.

$21.01

TUBE-WATER

$100.14

Icemaker Motor Kit

This kit includes the module motor, ejector arm, and ice stripper arm. The complete icemaker is sold separately.

$30.64

Thermostat Order 542369 Cement

The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ice into the bin and start the ice making cycle again. If your ice maker is making unusual noises, or if the ice maker is not making or dispensing ice, there could be an issue with the thermostat. Before you begin this repair, make sure the power is disconnected from your refrigerator, and that any food that may spoil is safely stored. This is an OEM part and is sourced directly from the manufacturer. This thermostat is sold individually, and comes with two attachment clips.

$17.57

Water Fill Cup and Bearing

This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ic...

$25.11

Shut Off Arm

This is a shut off arm for the ice maker in a refrigerator. When the shut off arm has reached maximum height, it triggers the switch to shut off the ice maker so it does not continue to make ice until the level of ice in the ice bucket begins to drop. The ice maker can also be shut off by lifting the shut off arm past the maximum height and into the locked position. This part is made of metal, and measures approximately 9 inches wide and 4 inches tall. This is an OEM replacement part.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 519 of 609 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 120 of 131 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more

Ice Maker stopped working

  • Customer: Robert from Port Washington, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 121 of 140 people found this instruction helpful
With socket wrench un-screwed the 3 screws and pulled out the ice maker assembly.

Pulled off white plastic end-cap and noticed the plastic gear disk had snapped off (sub part # R0167202)

However, it is all-one-part of the motor assembly unit # w10190935 (part # PS2341896) which must be ordered as a complete part.

Unscrewed t... read more