EB802 Shindaiwa Leaf Blower / Vacuum - Overview

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. ...Read moreIf the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

This breather, also known as a fuel tank vent, is a genuine OEM replacement part used in trimmers and edgers. It is responsible for managing the pressure and air flow inside the fuel system, by acting as a valve for the fuel tank. It allows clean air to enter the tank, while preventing dirt and debris from entering as well. Over time, the...Read more breather can crack or become clogged leading to restricted air flow, inconsistent fuel supply, fuel leakage, hard starting, and engine stalling. Locate the breather on or near the fuel tank and disconnect the hoses and fasteners attached to it. Depending on your model you may need to remove the fuel tank to complete this replacement. Place the new breather in position and reattach the hoses and fasteners. Test the new part by gently blowing into the breather to confirm that the air flow is not restricted.

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. T...Read morehis gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This is an authentic OEM sourced replacement tank that is specially designed for use with Shindaiwa handheld lawn and garden equipment. It is made of high-quality plastic and is sold individually, over time it may wear out or get damaged eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your mode...Read morel for the correct location and application of this item. Keep in mind the cap and other components are all sold separately.

This OEM Clip is a silver, steel part, which is sold individually. The part secures the fuel line to the fuel filter and is rated as Easy to install. You will know you need a new one if there is a leak around the hose where this clip is used to secure it, or if the fuel line detaches.

This is a genuine OEM replacement part used with backpack blower straps. This small plastic piece is used as a strap retaining device. It attaches the straps to the frame of the machine, and is designed to be unhooked quickly for easy adjustment. This part is sold individually.

This air purge body assembly is a genuine OEM component. It is specially designed for Echo and Shindaiwa handheld lawn and garden equipment. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in ...Read morethe fuel return line. At some time the primer will lose its elasticity or crack and need to be replaced. It is a complete assembly which includes the plastic body housing and the rubber bulb. To ensure the correct installation of the new part, refer to the diagrams of your specific model. You will need a screwdriver to remove the old assembly and connect the new one.

This is a genuine OEM part. The fuel line grommet w/vent tube is constructed of plastic parts and is compatible with trimmers, edgers, blowers and brushcutters. This item is fastened onto the fuel tank, moving the fuel to the breather assembly. This Shindaiwa part is sold individually. The fuel tank assembly (P021028090) also includes thi...Read mores component. A screwdriver is often helpful in the removal and replacement. Please be sure to refer to specific manual and diagrams for repair instructions.

This genuine Primer Cover, or Primer Pump Cover, is a silver, individually sold, steel part with dimensions of around 1x1 inch. This part is installed using a screwdriver, and is rated as Easy to install by our customers. This part secures the plastic primer bulb to the air purge body assembly, and must be replaced if damaged or bent.