EB5000IA Honda Generator - Overview

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is an authentic Honda replacement part, sourced from the original manufacturer for use with small engines. The special hex head bolt is commonly used to secure the ignition module assembly. This flanged bolt is available as an individual replacement part, please see illustrated part list for associative parts.

This gasket is a genuine OEM replacement part designed to seal the area between the exhaust pipe and cylinder head. It has a length of 3 inches and a width of 1.5 inches. The gasket prevents exhaust gases produced during combustion from escaping through the connection points and prevents air from entering the exhaust system. A faulty gask...Read moreet will result in increased emission of harmful gases, overheating, increased noise, and overall lower engine performance. You will likely need to remove the exhaust pipe to access the gasket. Once the gasket is removed, clean the surface to ensure a good seal and place the new gasket in position. Reconnect the pipe and ensure all parts are secure.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This rubber fuel strainer cup gasket, found in your garden equipment, distributes pressure and creates a seal between the fuel strainer cup and the carburetor so that fuel does not leak. If it is broken, you will notice fuel leakage or a gas smell, and your engine may sputter or have difficulty starting. Unattended fuel leaks not only was...Read morete fuel but also pose a fire hazard. When removing the gasket, make sure that your machine is shut off and has cooled down. Consult your instruction manual to locate the fuel strainer cup, remove mounting screws and clips with a screwdriver, twist the cup slightly, and lift it away. Peel off the old gasket carefully. It is important to be aware that this authentic OEM replacement part is sold individually.

This item is an authentic OEM part which is made for use with Honda engines commonly installed on a variety of lawn and garden equipment. The clip is utilized to secure the fuel tube. If the clip is damaged or is missing, this will provide an identical replacement for a missing or a damaged component that was installed on a new unit. Chec...Read morek the diagrams of your model for the exact location and the correct application of this hardware. One durable metal clip is included. You may need pliers to secure and remove it.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This OEM-manufactured flange bolt provides a secure connection between two parts of your equipment. What is different about a flange bolt is that it has a wide, flat flange at the end. This helps to distribute the load being applied to it and prevents the bolt from becoming loose. Flange bolts are commonly found in lawn equipment, but the...Read moreir location varies by the make and model of the machine. When damaged, the part that the flange bolt was holding may loosen and fall off. You also may observe that it the flange bolt is cracked or corroded. It is important for you to replace broken flange bolts immediately as loose or vibrating parts can detach from your equipment while it is operating. You need a socket wrench to remove a flange bolt, as well as rust dissolver or penetrating oil if it is stuck. This replacement part is sold individually so make sure that you consult your user guide to identify where your flange bolts are and how many your equipment needs.

It is a genuine manufacturer-approved replacement gasket which is designed for use with Honda engines that are commonly installed on lawn and garden equipment. The purpose fo this part is to create an air-tight seal between the carburetor and the stay assembly, please make sure to check appropriate diagrams of your model for correct locat...Read moreion and use of this item. Over time gaskets tend to deteriorate and crack eventually requiring replacement. It is made of durable composite material and it is sold individually.

This collar is an authentic manufacturer-supplied part which is specially made for Honda engines commonly installed on a variety of lawn and garden equipment. It is an identical replacement for a faulty or a missing hardware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and...Read more the correct application of this component. A wrench set will be needed to secure or remove the hardware that holds this part. This high-quality collar is made of durable metal and is sold as an individual item.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover