EB2800I (Type AVIN# GCAAA-1496157-9999999) Honda Generator - Overview

This genuine OEM air cleaner element is also known as an air filter, and it is found in the air filter housing or air intake system of your lawn equipment. It removes dust and debris from the air entering the engine to safeguard it from damage. It is a paper element with an orange frame. If the cleaner element appears damaged or excessive...Read morely clogged with debris, it needs replacement. For this simple replacement, no tools are needed. Press the retaining tabs down to release the air filter housing cover. With the cover removed, pull the old cleaner element off by hand. Install the new air cleaner by placing it in the housing and aligning the lower cover tabs with the housing and then snap the upper tabs into place. Install the new cleaner element by positioning it in the housing then align the lower cover tabs with the housing and snap the upper tabs into place. It is recommended that you check your air cleaner element every three months and replace it if necessary. Since this replacement part is sold individually, it is a good idea to keep extras on hand for regular equipment maintenance.

This is a genuine Honda replacement spark plug. It is sourced directly from original equipment manufacturer and it is sold individually. It is designed to ignite the air fuel mixture by the spark. If spark plugs are not checked with regular services, cleaned or changed when necessary, they can cause problems to occur with the engine. Replacing it you should only need a spark plug socket.

This genuine item is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. It is the main cover for the cylinder assembly. The part helps to protect the internal components from dust and other contaminants. If your cover is damaged or is missing,...Read more this will provide an identical replacement for the original component that was installed on a new unit. This high-quality head cover is made of durable metal and is sold individually. Note, the hardware to secure it is sold separately. You will need a wrench to perform this repair.

This is an OEM spark plug designed for engines to ignite the air-fuel mix inside the combustion chamber. This plug is white and silver and made of metal and ceramic materials. Over time the spark plug can become fouled due to a range of reasons including a poor air-to-fuel ratio worn piston rings carbon-build-up and general wear and tear....Read more You can clean a lightly worn spark plug with fine sandpaper and carb cleaner and re-install but generally you are going to have to replace this part often and it is better to replace a fouled plug than try to clean it. If your spark plug is in bad condition you may experience a missed start or a no-start situation. If the engine has 2 or more cylinders you can pull the spark plug wire off to see if the RPMs are dropping due to a miss. On a single cylinder a malfunctioning spark plug is more likely to cause a no-start issue. When replacing the spark plug be sure you torque to the manufacturer specs. Most customers found this repair easy you will just need a spark plug socket.

This is an exhaust valve rocker arm used for small engines and equipment like pressure washers. Rocker arms transmit motion from a camshaft to valves, controlling valve timing and duration. If your engine struggles to start, misfires, or will not start, inspect the rocker arm(s) for excess play, wear, or bending due to high temperatures. ...Read moreTo replace it, disconnect the spark plug and/or starting coil, remove the valve cover, and locate the rocker arm(s). Rotate the camshaft until pistons are up and rocker arms are loose. Slide out the pin, remove the old rocker arm, and install the new one with its pin. Tighten the adjustment screw to the manufacturer specifications, reinstall the spark plug, replace valve cover sealant, and reattach the cover.

This item is an authentic Honda replacement part and has been sourced from the original manufacturer to be used with small engines. The seal is used to prevent oil from leaking from between the crankcase and the crankshaft. The oil seal is available as an individual replacement part.

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is an authentic Honda replacement part, sourced from the original manufacturer for use with small engines. The special hex head bolt is commonly used to secure the ignition module assembly. This flanged bolt is available as an individual replacement part, please see illustrated part list for associative parts.

This is an authentic Honda replacement part that has been OEM sourced to ensure a high-level of quality. The timing belt is intended to be used with small engines. This used to link the crankshaft and the camshaft pulley to ensure the two parts rotate in unison. This item is available as an individual replacement part. A socket ratchet se...Read moret, wrench set, torque wrench, flat-head screwdriver, small nose pliers, tubing clamps are some tools that may be needed to install the belt.

It is an authentic replacement o-ring that is supplied by original equipment manufacturer for use with Honda engines. This is the item that creates a seal between the camshaft pulley and the shaft, for correct application please make sure to check appropriate diagrams of your model. Over time the material may deteriorate and crack allowin...Read moreg for leaks, if this happens the o-ring will need to be replaced. Please note this durable rubber item is sold individually.

This is a genuine manufacturer-approved component which is specially made for use with Honda engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or a faulty nut that helps to secure the tappet adjusting screw. Please make sure to refer to the appropriate diagrams of your model for the corr...Read moreect location and application of this hardware. Keep in mind this high-quality part is made of durable metal and is sold individually.

This is an authentic manufacturer-sourced part that is specially designed for use with Honda engines commonly installed on lawn and garden equipment. It is an identical replacement for a faulty or a damaged tappet adjusting screw that was installed on a new unit. The purpose of this item is to secure a valve rocker arm, please make sure t...Read moreo refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality part is made of durable metal and is sold individually.