EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EA2111 Speed Queen Washer - Overview

Diagrams for EA2111

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
V-Style Drive Belt (32.5 inches long) – Part Number: WP28808
$57.38
Special Order
V-Style Drive Belt (32.5 inches long)
★★★★★
★★★★★
(4)
Part #WP28808
This v-style drive belt is thirty-two and a half inches long and half of an inch wide.
Affresh Washing Machine Cleaner - 3 pack – Part Number: W10135699
$20.36
Special Order
Affresh Washing Machine Cleaner - 3 pack
★★★★★
★★★★★
(2)
Part #W10135699
Affresh Washing Machine Cleaner includes three slow-dissolving tablets that help remove odor-causing residue from inside the washer. Suitable for all washer brands, including high-efficiency (HE) machines, the formula is also septic-safe. Place one tablet directly in the empty wash basket and run the Clean Washer cycle, or use a normal cycle with hot water. Use monthly or every 30 wash cycles for best results.
Inlet Hose - 5 FT – Part Number: WP89503
$19.30
In Stock
Inlet Hose - 5 FT
★★★★★
★★★★★
(4)
Part #WP89503
This hose can handle hot or cold water and is five feet long.
Affresh Washing Machine Cleaner Tablets – 6 Count – Part Number: W10501250
$28.42
In Stock
Affresh Washing Machine Cleaner Tablets – 6 Count
Part #W10501250
This Affresh Washing Machine Cleaner deep cleans to help remove the odor-causing residues and grime that daily loads leave behind. The time-release tablets are EPA Safer Choice certified, septic-safe and designed to clean inside all machines, including HE (High Efficiency). Use monthly or every 30 cycles for a consistently clean machine.
V-Style Cogged Pump Belt (22.5 inches long) – Part Number: WP27155
No Longer Available
V-Style Cogged Pump Belt (22.5 inches long)
Part #WP27155
This V-style cogged tooth pump belt is used in conjunction with the drive belt in your washing machine. This belt is all black in color and is made entirely of rubber. It is twenty-two and a half inches long and 3/8 of an inch wide
Lid Switch – Part Number: WP27001095
No Longer Available
Lid Switch
Part #WP27001095
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
Brake Rotor Assembly – Part Number: R9900474
No Longer Available
Brake Rotor Assembly
Part #R9900474
Mix Valve to Tub Cover Hose – Part Number: 38155
No Longer Available
Tub Cover Gasket – Part Number: WP32857
No Longer Available
Tub Cover Gasket
Part #WP32857
Drain Pump - 2 Port – Part Number: 31969
No Longer Available
Drain Pump - 2 Port
Part #31969
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Two Speed Motor – Part Number: 27179P
No Longer Available
Two Speed Motor
Part #27179P
This two speed motor performs 1725 revolutions per minute in one speed, and 1140 revolutions per minute in the second speed. It runs at 1/2 horsepower and carries 115 volts. You can use this washer motor with your Amana brand washing machine. This motor replaces those models that utilize two pulleys and whose pump is belt driven.

Common Symptoms of the EA2111

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Frayed V-belt
63 of 70 people found this instruction helpful.
  • John from Milton, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, r emove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
Was this helpful?
Thank you for voting!
The Seal On The Bottom Of The Tub Was Leaking
34 of 43 people found this instruction helpful.
  • HOWARD from CORTLAND, OH
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forward. Primed the pump and started the machine for the stated time and was a sucess.
Was this helpful?
Thank you for voting!
Leaking water from outer tub
19 of 22 people found this instruction helpful.
  • Michael from La Porte, TX
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
After removing the front panel, and taking the (2) screws out securing the top (which lifts uplike the hood of a car) I removed the outer tub plastic ring using (4) screwdivers to lift in various spots to release ,which was pretty easy. They used to make a special tool for $55.00, but you don't need it. What I found when I removed the pla stic ring was that the outer tub had (3) holes rusted through at the very top. After sanding them down to bare metal, I J.B. Welded them, let that cure, and then put the new gasket in the plastic outer ring. I backed up the new ring gasket with RTV silicone, snapped it back on, and let that sit for 24 hours. Then I replaced the fill hose from the water mixing valve to the tub ring, which distributes the water into the basket. Easily done in 5 minutes with a regular scewdriver and a pair of pliers. You will need to have an additional 5/8" - 1" hose clamp to replace one of the original snap-style hose clamps, since it gets very rusty over time. Everything works great now. This washer is 13 years old, and I just wanted to buy another 6-12 months when we will buy a new one. (Have you seen the prices on new washers lately!?!?) Took a few hours to repair, but only cost about $40 bucks. Besides, my motto is "If a man can build it, I can take it apart!"
Was this helpful?
Thank you for voting!