Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
This infinite control switch regulates power to a surface burner, allowing smooth and adjustable heat control. Reliable switching improves cooking accuracy and safety. Replacing a faulty switch helps restore consistent burner operation.
This 6-inch surface heating element delivers steady, even heat for everyday cooking tasks. Designed for consistent performance, it is commonly replaced when a burner fails to heat, heats unevenly, or stops working entirely, restoring dependable cooking functionality.
This dual radiant surface element is designed for use in electric ranges and cooktops, providing efficient and responsive heat for cooking. It features a 6-inch, 1200-watt inner ring and a 9-inch, 2500-watt outer ring, allowing for flexible heating options depending on pan size and cooking needs. Ideal for replacing a non-functioning or u...Read morenevenly heating element, this part helps restore consistent performance to your appliance. Always disconnect power before installation.
This dual radiant surface bridge element is designed to supply consistent heat to the cooking surface of electric ranges and cooktops. Positioned beneath the glass top, it warms through a radiant coil to support a variety of cooking tasks. With a power rating of 1800/2600 watts, it’s ideal for replacing a failed heating element and restor...Read moreing full functionality. Compatible with multiple appliance brands, this part should be installed only after disconnecting the appliance from its power source.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cord was not tightened enough by delivery crew.
109 of 174 peoplefound this instruction helpful.
Timothy from Spring Valley, AL
Really Easy
15 - 30 mins
Screw drivers, Socket set
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read mored are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Was this helpful?
Thank you for voting!
The elements were not heating up
6 of 8 peoplefound this instruction helpful.
Tanya from KALISPELL, MT
Really Easy
15 - 30 mins
Screw drivers
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this helpful?
Thank you for voting!
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 peoplefound this instruction helpful.
Daniel from Falmouth, MA
A Bit Difficult
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely. Once all was replaced and reinstalled the oven
... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.