Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Faceplate for icemaker fell off, breaking ribbon cable
3 of 3 peoplefound this instruction helpful.
Wayne from MARLBOROUGH, MA
Really Easy
30 - 60 mins
Ordered new ribbon cable. At first I couldn't figure out how to get the wide end of the ribbon cable off, and I took the whole inner circuit board out - in fact, all it needed was more muscle, a straight pull out, no clips or anything holding it in other than friction. The narrow end attached to the control button board has two clips whic
... Read moreh pull towards you to loosen the ribbon. Easy install, worked perfectly
Read less
Was this helpful?
Thank you for voting!
Broken Drum
3 of 3 peoplefound this instruction helpful.
Jubal from OZARK, AL
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.
Was this helpful?
Thank you for voting!
Support pins snapped off.
3 of 3 peoplefound this instruction helpful.
Fred from SPRING LAKE, NC
Really Easy
Less than 15 mins
Followed video on your site. It was very helpful. Thank you.
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Ice maker non functioning, Ice maker not sending signal for w
4 of 6 peoplefound this instruction helpful.
Marcus from Bessemer, AL
Really Easy
15 - 30 mins
Socket set
Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.
Was this helpful?
Thank you for voting!
Replaced Ice Maker
3 of 3 peoplefound this instruction helpful.
Robert from Franklin, TN
Really Easy
15 - 30 mins
Socket set
Unplugged refrigerator from the wall plug. Removed ice tray cover, removed ice container, lossen the two screws on the ice marker holding it to the back of the fridge, dropped the ice marker down and unplugged the electrical connection. Then removed the ice maker. Took the new ice marker, plugged the electrical connection back into t
... Read morehe back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place. Replaced the ice container, replaced the ice cover. Plugged the fridge electrical cord back in to the wall socket. Done. It started making ice again in about 10 minutes.
Read less
Was this helpful?
Thank you for voting!
the closer plate was cracked and caused the door to catch and make a popping sound.
3 of 3 peoplefound this instruction helpful.
Cathy A from HAMILTON, MT
Really Easy
15 - 30 mins
Screw drivers, Socket set
the repair was so easy to do. it did take 2 of us to handle the door removal and reinstallation. we watched the video and carefully removed the door and had no trouble at all with the new parts installation. we knew what to expect and successfully fixed the frig! Good Deal!! Easy fix!!
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
4 of 7 peoplefound this instruction helpful.
Jack from WALLING, TN
Really Easy
15 - 30 mins
Nutdriver, Socket set
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off
... Read moreand extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Read less
Was this helpful?
Thank you for voting!
Broken clear plastic shelf
4 of 7 peoplefound this instruction helpful.
David from VALENCIA, CA
Very Easy
Less than 15 mins
Simply remove & replace No tools required
Was this helpful?
Thank you for voting!
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
3 of 4 peoplefound this instruction helpful.
Melissa from Olden, TX
Really Easy
15 - 30 mins
Screw drivers
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
Was this helpful?
Thank you for voting!
Replace cracked gallon door bin
4 of 7 peoplefound this instruction helpful.
Ralph from Fountain Inn, SC
Really Easy
Less than 15 mins
Easy to order on line. Access to schematics let me pick the right part.Fast delivery in two days. Easy to install. slide up and out . Slide new one in. Thanks for quick service.
Was this helpful?
Thank you for voting!
Ice maker was over filling.
5 of 10 peoplefound this instruction helpful.
Richard from Marco Island, FL
Easy
Less than 15 mins
Screw drivers
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.
Was this helpful?
Thank you for voting!
No water to ice maker
3 of 4 peoplefound this instruction helpful.
Joel from SODUS POINT, NY
Really Easy
30 - 60 mins
Nutdriver, Wrench (Adjustable)
Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back o
... Read moren. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.
My Orders
