Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E23CS75DSSE > Parts

E23CS75DSSE Electrolux Refrigerator - Parts

All parts for the Electrolux Refrigerator E23CS75DSSE

Below is a list of all parts for the Electrolux Refrigerator E23CS75DSSE - Side-by-side. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the E23CS75DSSE
1-14 of 312
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.15

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$60.81

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line when activated, and send it through to your water dispenser in your refrigerator. To make this repair you will need an adjustable wrench, a quarter inch nut driver, and a sharp utility knife. Before you begin this repair make sure to disconnect the power supply to your refrigerator, as well as disconnect the inlet water supply from the back of the refrigerator. Note that this part may appear different than the original, but is an authorized manufacturer replacement.

$4.33

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, an...

$8.63

Hinge Bearing

Sold individually.

$100.41

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice i...

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.

$40.90

Crisper Drawer Cover - NO Glass

This part contains molded glide rails for the crisper pan. It does not come with the glass shelving. The glass is not included. Must be ordered separately.

$29.24

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refrigerator or freezer section will not start, if they are too warm, or if your refrigerator has become too noisy. Replacing the run capacitor is a relatively easy project. For this repair you will only need a 1/4 inch nut driver and needle nose pliers. Remember to disconnect the power and water supply line to the unit before you begin this repair. For full step by step instructions, simply click on the video below.

$105.86

Rear-Mount Ice Maker Assembly

This kit includes the ice maker, power cord, bail arm, and fill cup. If your ice maker is not making or dispensing ice, or you notice a leak, you may need to replace the rear-mount...

$29.07

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$45.75

Meat Pan Cover Frame - Glass NOT Included

Glass insert must be ordered separately.

$31.27

Dispenser Crusher Housing

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

$14.75

Ribbon Cable Harness

Used in the dispenser board area.

$8.59

LIGHT BULB

This light bulb is used on the inside of your refrigerator or freezer. It is blue in color.

All Parts for the E23CS75DSSE
1-14 of 312