E23BC68JPS6 Electrolux Refrigerator - Instructions

In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the ... Read more valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if t ... Read more he maker dumped the ice into the bin.

pulled fridge from wall, removed card board cover, unplug the fridge. turn the water off to the fridge. remove the water source from fridge first then remove 2 screws that hold the valve. then the wire plugs. hoses.. they were color coded.

Repair was very easy - and to my great delight, they have replaced the old-style compression fittings with PEX push-fittings. You just clip the old compression ring and nut off the tubing and insert the tubing firmly into the fitting. SNAP! VOILA! PEX fittings are the greatest things since sliced bread. I used it to plumb my new house ... Read more .

turned off water supply at water line to fridge. removed two hex head screws @ bottom of rear of appliance that hold the water valve in place.
Simply moved color coded elect. plugs from old one to new one, same with water lines. Only difference is, the replacement one I got uses push in water lines and my original was compression ... Read more fit. No problem though, just cut the nipple off of original line going into new valve and you are good to go. Might want to have an extra 1/'4" brass compression washer though for the one remaining line. Whole process I did on my lunch break at home less than 30 minutes.
Only problem though was nothing changed. Spoke with service man over the phone and he said MOST of the time it is water freezing up in the inlet tube top of machine, inside. Remove water line from rear outside on top behind freezer and with a straw try to blow through, if it is froze it will not go through. Mine did not go through. Used hair dryer inside freezer in back on incoming line 5-10 minutes,thawed out, makes ice. Go figure. Changing valves was easy and well described as stated, just not necessary in my case, but now I know. Thanks, Warren in Iowa

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used ... Read more my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!

1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions prov ... Read more ided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wir ... Read more es cut and spliced and viola fixed.

Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searc ... Read more hes on the internet to finally figure this part out. From there on out it went smoothly. Old base came out with two screws. Reversed process for reinstall of new base. Water hoses just slipped back into place and locked themselves in. Just takes a little patience.

The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water va ... Read more lve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of wate ... Read more r

took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim

Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. I ... Read more f you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the a ... Read more bove procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.