DWS780-AR (1) DeWALT Miter Saw - Overview

Sold Individually. This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.

This is a genuine Dewalt replacement part, it is sold individually. The purpose of the Blade Adapter, is to make the bore of a blade that is 1 inch and reduce to a 5/8 inch bore. Making it possible to use a 1 inch bore blade on a 5/8 inch arbor.

This is a genuine manufacturer sourced replacement part designed for use with Dewalt miter saws. This wear plate helps to minimize the friction and avoid potential wear to the table assembly. It is made out of plastic and it is sold individually.

This replacement screw is an authentic manufacturer sourced item. It is commonly used with a variety of power tools. This screw is a standard hardware which has multiple uses based on equipment. To ensure correct location and application of this item please make sure to check appropriate diagrams. It is made out of metal and it is sold in...Read moredividually. Requires a torx or a flat-head screwdriver to tighten/loosen this screw.

This replacement screw is a high quality hardware commonly utilized on Bostitch, Black and Decker, Porter Cable and Dewalt equipment. This is a authentic OEM item which has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

This Ball Bearing is sealed on both sides. It is a genuine replacement part and is sold individually. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the too...Read morel and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine manufacturer-approved replacement part which is specially designed for DeWALT saws. Bushings are generally utilized to provide a tight fit between connected components while allowing for movement with minimum friction. If the bushing is damaged or is missing, this will provide an identical replacement for the original ha...Read morerdware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the proper repair procedure. Note, this high-quality part is sold individually.

Genuine Dewalt replacement part, this item is sold individually. The purpose of the 394589-01 Screw is used to secure the pivot plate on the Miter Saws listed below. You can use a flat blade screwdriver or a Torx T-30 bit on this screw.

This is a genuine manufacturer approved replacement part designed for use with Dewalt miter saws. This bushing helps to secure the blade to the shaft/spindle. It is made out of metal and it is sold individually. To replace it you would need a wrench to remove the blade bolt.

Included in part number 606883-00

This needle bearing is open on one side and closed on the other. This genuine DeWalt replacement part is sold individually. • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. ...Read moreThis reduces wear on the tool, allowing it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

It is a genuine item that is supplied directly from the original manufacturer for use with DeWALT compound miter saws. The lever provides a user with a comfortable grip to lock the bevel at the desired angle. It provides an identical replacement for a faulty or a missing component that was installed on a new unit. To ensure the correct in...Read morestallation of this lever, refer to the diagrams of your model. One durable plastic part is included. Note, the hardware to secure it is sold separately. You will need a socket wrench to remove and resecure the nut that holds this lever.