DWFP1838R (Type 1) DeWALT Nailer - Overview
Sections of the DWFP1838R
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
HEAD VALVE BODY
PartSelect #: PS12417689
Manufacturer #: 180450-S
This head valve body regulates airflow within pneumatic nailers, helping generate the pressure needed to drive fasteners effectively. Built from durable materials, it supports consistent tool performa...
$6.40
In Stock
PISTON RING
PartSelect #: PS18995697
Manufacturer #: N905972
Genuine OEM replacement part, this item is sold individually. The purpose of this part is to keep air pressure in the cylinder of the tools listed below. If you have an air leak in your pneumatic too...
$6.40
In Stock
O RING
PartSelect #: PS12420389
Manufacturer #: 180448
This is an authentic Bostitch replacement part used on specific Nailers. This is a Rubber Ring and it is sold individually. O-rings are designed to withstand thousands of pounds of pressure by creatin...
$6.40
In Stock
SPRING
PartSelect #: PS12417694
Manufacturer #: 180527
This is an authentic replacement part that has been sourced from the original manufacturer to be used with pneumatic fasteners from Bostitch, Porter Cable, and DeWalt. The metal spring is part of the ...
$6.40
On Order
WASHER FLAT
PartSelect #: PS12425945
Manufacturer #: 180449
This is an authentic OEM product which is designed for Bostitch, DeWALT and Porter Cable nailers and staplers. It provides a tight seal for the valve piston. Over time the material may wear down causi...
$6.40
In Stock
FOOT-CONTACT (NO MAR
PartSelect #: PS12420362
Manufacturer #: 179760
This is a genuine Bostitch replacement part, it is sold individually. The Contact Foot is attached to end of the trip assembly to prevent the material that it is being used on from getting marred or ...
$6.40
In Stock
GASKET-END CAP
PartSelect #: PS12425947
Manufacturer #: 180463
It is a genuine manufacturer-approved replacement gasket which is specially produced for use with Bostitch nailers and staplers. This gasket provides an air-tight seal for the end cap. over time it ma...
$6.40
On Order
O-RING-44.7MMX2.4MM
PartSelect #: PS12401156
Manufacturer #: 180459
This replacement part is supplied directly from the original equipment manufacturer for use with Bostitch nailers and staplers. It is utilized to provide an air-tight seal for the cylinder sleeve, ple...
$6.40
In Stock
END CAP
PartSelect #: PS12423284
Manufacturer #: 180465
This is a genuine manufacturer-sourced component which is specially designed for use with Bostitch nailers and staplers. It provides an identical replacement for a missing or a faulty end cap that was...
$10.17
In Stock
SPRING
PartSelect #: PS12425944
Manufacturer #: 180447
This is a genuine OEM sourced part that is intended to be used with pneumatic nailers and staplers from Bostitch, Porter Cable, and DeWalt. The metal spring is used to provide compression between the ...
$6.40
In Stock
SCREW-SHCS-M4X0.7X16
PartSelect #: PS12478636
Manufacturer #: MSC4070-16
This replacement screw is a high quality item that has multiple uses depending on the model of your tool, please make sure to check appropriate diagrams for correct location and use of this hardware. ...
$6.40
In Stock
Common Symptoms of the DWFP1838R
[Viewing 3 of 3]Won't fire
Fixed by
these parts
these parts
Show All
Leaks air from top
Fixed by
these parts
these parts
Show All
Driver won't return
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken magazine end cap prevents magazine from latching closed
1. Use belt clip on staple gun to hold in place on workbench.
2. Use a hammer with a punch or small screwdriver to hit the two pins holding the end cap to the magazine. Repeat ad nauseum with as much force as you can muster until both pins come out and the broken end cap can be removed.
3. Align new end cap on magazine and use s ... Read more ame procedure to drive pins. Exercise caution with the shorter of the two pins. If not perfectly aligned, the plastic tabs on the end cap can easily break off.
2. Use a hammer with a punch or small screwdriver to hit the two pins holding the end cap to the magazine. Repeat ad nauseum with as much force as you can muster until both pins come out and the broken end cap can be removed.
3. Align new end cap on magazine and use s ... Read more ame procedure to drive pins. Exercise caution with the shorter of the two pins. If not perfectly aligned, the plastic tabs on the end cap can easily break off.
Read less
Parts Used:
-
Matthew from Morton Grove, IL
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!