DWE7800 (Type 1) DeWALT Sander Polisher - Overview

Help restore your tool's performance with this carbon brush, designed to maintain electrical contact between the motor's stationary and rotating components. As brushes naturally wear over time, replacing a worn brush can help resolve issues such as reduced power, intermittent operation, excessive sparking, or motor stalling. Made for reli...Read moreable electrical transfer and consistent motor performance, this replacement brush is sold individually. Since most compatible tools use two brushes, replacing both at the same time is recommended for balanced wear and optimal operation. Refer to your tool's parts diagram or service manual to confirm the correct application before installation.

This item is a genuine Porter Cable replacement part and has been sourced from the original manufacturer to be used with drywall sanders. The plastic hose is used to ling the hose adapter to the longer hose to collect dust to reduce the amount of drywall dust in the air. This item is available as an individual replacement part.

This is a genuine replacement part sourced from the original manufacturer for use with power tools. The metal screw is commonly used with several different types of power tools, and the application of the screw can vary based on the model of the power tool. This screw is available as an individual replacement part, please see model diagram for part location and usage.

This is a genuine OEM sourced replacement guide pin that connects to the pivot plate. It is designed for use with Porter Cable drywall sanders. It is made out of metal and it is sold individually. No tools are needed to replace it.

Keep your tool running smoothly with this brush holder, designed to securely hold the carbon brush in place and maintain proper contact with the motor's armature. A worn or damaged brush holder can lead to poor electrical contact, reduced performance, or intermittent operation. Replacing it helps restore reliable motor function and consis...Read moretent power delivery. Designed as a direct replacement for the original component, it is ideal for maintaining the performance of your tool. Refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

Keep your tool running reliably with this brush holder, designed to securely position the motor's carbon brush and maintain consistent contact with the armature. A worn or damaged brush holder can lead to poor electrical contact, reduced performance, or intermittent operation, making replacement an important part of motor maintenance. Des...Read moreigned as a direct replacement for the original component, it helps restore proper brush alignment and dependable motor function. Refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

This is a Genuine OEM sourced replacement part designed for Porter Cable Drywall Sanders. This item is made out of Metal and it is Sold Individually. Over time the square ends of the Flex Shaft will become rounded and the unit will cease to operate correctly. You would need a Screwdriver and Pliers to replace this item.

This is a genuine OEM approved replacement part designed for use with Porter Cable drywall sanders. It extends below the surface of the abrasive pad to prevent the abrasive from "gouging" the work. It helps to contain the drywall dust until the vacuum cleaner pulls it away. It is made out of metal with plastic and it is sold individ...Read moreually. To complete this repair you would need a screwdriver. • Remove abrasive pad • Use phillips screwdriver to remove the six retaining screws • Lift the skirt out of housing • Position the new skirt to the housing and install the six retaining screws • Replace the abrasive pad

It is a genuine replacement screw that is sourced directly from original equipment manufacturer. This is a standard hardware that has multiple uses depending your tool. For correct location and use of this screw, please check appropriate diagrams. This torx screw is sold individually.

This plastic switch is supplied by the original manufacturer. It is used in DeWALT small angle grinders. This is a push-button switch controlling on-off functions. One (1) switch is included. Please note that linkage and button slider are sold separately. • Disassemble housing • Remove wiring from the old switch • Disconnect switch from linkage • Reconnect new switch and reassemble housing

This is a casing for the drive shaft cable of a drywall sander, crafted from durable rubber and metal, and is an authentic OEM part. Over time, prolonged use, or in case of damage, replacing this casing is essential for your sander to maintain optimal functionality and to prevent dust accumulation around critical mechanical joints. To rep...Read morelace the casing, gather a screwdriver and wrench. Start by removing the pins securing the yoke to the pivot assembly of the sander. Next, pull the boot off the casing and proceed to remove the screws fastening the casing to the boom arm. Unfasten the other end of the casing from the sanding pad. Remove the casing from the shaft, and detach the boot and flange from the old casing to install them onto the new casing. Before installing the new casing, inspect the drive shaft for potential damage, as it might need replacement as well. Install the new casing onto the shaft and thread it onto the shroud. Screw the casing into the boom arm through its flange and reinstall the boot. Finally, resecure the yoke to the sanding pad by screwing in the pins on the other side.