DW744 (Type 3) DeWALT Table Saw - Overview

This brush and holder assembly is a genuine Dewalt replacement part, not aftermarket or generic. _b_This item is sold individually_/b_. As pictured, this item includes everything you need to replace a brush in your power tool. The brush, holder, terminals, and spring are included and ready for installation. If you only need the carbon ...Read morebrush and not this entire holder assembly, you can purchase the brush separately (see the 'Related Items' section below). This brush and holder is compatible with the tools listed below, but it is not guaranteed to fit any other power tools. It is advised that you replace both brushes only if you think all you need is one.

This replacement screw is a genuine OEM sourced hardware that is specially designed for with Delta, Dewalt and Black and Decker power tools. This screw is a standard hardware which has multiple uses based on equipment, to ensure correct application of this item please make sure to check appropriate diagrams of your unit. One durable torx screw is included per order.

This replacement screw is an authentic manufacturer sourced item. It is commonly used with a variety of power tools. This screw is a standard hardware which has multiple uses based on equipment. To ensure correct location and application of this item please make sure to check appropriate diagrams. It is made out of metal and it is sold in...Read moredividually. Requires a torx or a flat-head screwdriver to tighten/loosen this screw.

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

This replacement screw is a high quality hardware commonly utilized on Bostitch, Black and Decker, Porter Cable and Dewalt equipment. This is a authentic OEM item which has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

This Genuine OEM carbon brush is an essential replacement part designed for use with a variety of DeWALT and Black & Decker saws. Sold individually, this high-quality component is made to conduct electrical current within the motor, enabling efficient power transfer and tool performance. Over time, carbon brushes naturally wear down due t...Read moreo friction and electrical contact, which can lead to intermittent motor issues or failure to start. Measuring 3/4 inch in length, 1/2 inch in width, and 1/4 inch in thickness, this brush is built to original specifications for a precise fit. When replacing carbon brushes, it’s important to also inspect the motor’s armature for signs of burns, cracks, or other damage, which may indicate a more serious issue. A hex key or screwdriver may be required for installation, depending on your tool model.

This is an original replacement part manufactured for use with DeWalt table saws. The plastic front support connects the work support to the fence, and to provide a pivot point for the work support. The front support is sold individually, please see model diagram for hardware used to fasten the support.

This is a genuine OEM sourced replacement part designed for use with a variety of power tools. This is a standard hardware which has multiple applications based on your tool. For proper use please refer to diagrams. This is a metal torx T20 metal screw which is sold individually.

This genuine manufacturer-sourced replacement washer which is specially designed for use with a variety of equipment. It helps to distribute the pressure evenly between connected parts, this is a standard hardware which has multiple applications depending on the model of your equipment, please refer to appropriate diagrams for the correct...Read more location and use of this part. This part is a high-quality washer which is made of durable metal and it is sold individually.

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

This is a genuine OEM replacement part designed for use with a variety of power tools. It is made out of metal and it is sold individually. It is a standard hardware which has multiple applications based on your tool. You would need a wrench to tighten/loosen this nut.