DW705 (Type 8) DeWALT Miter Saw - Overview

This is a genuine Dewalt replacement part, it is sold individually. The purpose of the Blade Adapter, is to make the bore of a blade that is 1 inch and reduce to a 5/8 inch bore. Making it possible to use a 1 inch bore blade on a 5/8 inch arbor.

This brush and holder assembly is a genuine Dewalt replacement part, not aftermarket or generic. _b_This item is sold individually_/b_. As pictured, this item includes everything you need to replace a brush in your power tool. The brush, holder, terminals, and spring are included and ready for installation. If you only need the carbon ...Read morebrush and not this entire holder assembly, you can purchase the brush separately (see the 'Related Items' section below). This brush and holder is compatible with the tools listed below, but it is not guaranteed to fit any other power tools. It is advised that you replace both brushes only if you think all you need is one.

This replacement screw is an authentic manufacturer sourced item. It is commonly used with a variety of power tools. This screw is a standard hardware which has multiple uses based on equipment. To ensure correct location and application of this item please make sure to check appropriate diagrams. It is made out of metal and it is sold in...Read moredividually. Requires a torx or a flat-head screwdriver to tighten/loosen this screw.

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

This replacement screw is a high quality hardware commonly utilized on Bostitch, Black and Decker, Porter Cable and Dewalt equipment. This is a authentic OEM item which has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

This Kerf plate is a genuine DeWalt replacement part. It is made of plastic with a slot in the middle for the saw blade to slide through. It has 3 screw holes on each side (6 in total) to firmly secure the kerf plate to your saw. rnrnKerf plates (also called kerf boards) are used to prevent excessive splintering, resulting in cleaner c...Read moreuts. Using the wrong kerf plate for your tool can give a rough edge to the material you’re cutting.

Genuine Dewalt replacement part, this item is sold individually. The purpose of the 394589-01 Screw is used to secure the pivot plate on the Miter Saws listed below. You can use a flat blade screwdriver or a Torx T-30 bit on this screw.

This Genuine OEM carbon brush is an essential replacement part designed for use with a variety of DeWALT and Black & Decker saws. Sold individually, this high-quality component is made to conduct electrical current within the motor, enabling efficient power transfer and tool performance. Over time, carbon brushes naturally wear down due t...Read moreo friction and electrical contact, which can lead to intermittent motor issues or failure to start. Measuring 3/4 inch in length, 1/2 inch in width, and 1/4 inch in thickness, this brush is built to original specifications for a precise fit. When replacing carbon brushes, it’s important to also inspect the motor’s armature for signs of burns, cracks, or other damage, which may indicate a more serious issue. A hex key or screwdriver may be required for installation, depending on your tool model.

This needle bearing is open on one side and closed on the other. This genuine DeWalt replacement part is sold individually. • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. ...Read moreThis reduces wear on the tool, allowing it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This OEM Universal dust bag fits all of the DEWALT miter saws. It comes with the adapter which is not sold separately. Please note some DW718 Models may require an adapter part #618240-00 to make it work. The purpose of the dust bag is to capture sawdust to keep your shop and your work surface cleaner.

The plastic dust duct attaches to the arm of the miter saw and directs the dust away from the device. This part is available individually and will need replacing if it becomes broken. The dust duct is for use in miter saws made by DeWALT and Black & Decker. This is a genuine replacement part sourced from the original manufacturer.