DW704 (Type 2) DeWALT Miter Saw - Overview

This is a genuine Dewalt replacement part, it is sold individually. The purpose of the Blade Adapter, is to make the bore of a blade that is 1 inch and reduce to a 5/8 inch bore. Making it possible to use a 1 inch bore blade on a 5/8 inch arbor.

This brush and holder assembly is a genuine Dewalt replacement part, not aftermarket or generic. _b_This item is sold individually_/b_. As pictured, this item includes everything you need to replace a brush in your power tool. The brush, holder, terminals, and spring are included and ready for installation. If you only need the carbon ...Read morebrush and not this entire holder assembly, you can purchase the brush separately (see the 'Related Items' section below). This brush and holder is compatible with the tools listed below, but it is not guaranteed to fit any other power tools. It is advised that you replace both brushes only if you think all you need is one.

This replacement screw is an authentic manufacturer sourced item. It is commonly used with a variety of power tools. This screw is a standard hardware which has multiple uses based on equipment. To ensure correct location and application of this item please make sure to check appropriate diagrams. It is made out of metal and it is sold in...Read moredividually. Requires a torx or a flat-head screwdriver to tighten/loosen this screw.

This is a genuine OEM replacement part. Sold individually. This kit was made to replace the old switch on the Miter Saws that was discontinued. It includes both handle halves, handle to carry saw, new switch, screws and wire terminals. It also includes an installation sheet. Flat head screwdriver is needed for repair. This switch...Read more is a common replacement part and is compatible with the Miter Saw models listed below.

This Kerf plate is a genuine DeWalt replacement part. It is made of plastic with a slot in the middle for the saw blade to slide through. It has 3 screw holes on each side (6 in total) to firmly secure the kerf plate to your saw. rnrnKerf plates (also called kerf boards) are used to prevent excessive splintering, resulting in cleaner c...Read moreuts. Using the wrong kerf plate for your tool can give a rough edge to the material you’re cutting.

Genuine Dewalt replacement part, this item is sold individually. The purpose of the 394589-01 Screw is used to secure the pivot plate on the Miter Saws listed below. You can use a flat blade screwdriver or a Torx T-30 bit on this screw.

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

This OEM Universal dust bag fits all of the DEWALT miter saws. It comes with the adapter which is not sold separately. Please note some DW718 Models may require an adapter part #618240-00 to make it work. The purpose of the dust bag is to capture sawdust to keep your shop and your work surface cleaner.

The plastic dust duct attaches to the arm of the miter saw and directs the dust away from the device. This part is available individually and will need replacing if it becomes broken. The dust duct is for use in miter saws made by DeWALT and Black & Decker. This is a genuine replacement part sourced from the original manufacturer.

This is a genuine OEM sourced replacement part designed for use with a variety of power tools. This is a standard hardware which has multiple applications based on your tool. For proper use please refer to diagrams. This is a metal torx T20 metal screw which is sold individually.

This item is a genuine DeWalt part that has been sourced from the original manufacturer. The retainer plate is intended to be used with miter saws. This item is part of the guard assembly and is used as a nut that secures the pivot plate. The retainer plate is priced as a single item.

This is a genuine Dewalt replacement part, it is sold individually. The purpose of this bolt is to secure the blade on the miter saw models shown below. It has a 1/2 " hex head. It is 1 inch long, with left hand threads.