My Orders
DVG55CG7100VA3 (0000) Samsung Washer - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$55.18
In Stock
Drive Belt
Part #6602-001655
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This goes between the drive motor and the dryer drum. The belt may have broken, which will cause the drum to not turn properly. You will need to ...Read morepull your dryer away from the wall and use your Phillips screwdriver to remove the screws on the back. This is an OEM product, shipped directly from the manufacturer.
Read less
No Longer Available
Thermistor
Part #DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of needing a new thermistor is the dryer cycle not working. Before installing this part, you should disconnect your dryer from its power sourc...Read moree. We also recommend you wear work gloves to protect your hands during this installation. To make this repair, the tools you will need include a multi-screwdriver, a Phillips head bit, and a flat-head bit.
Read less
$61.57
In Stock
Idler Pulley Assembly
Part #DC93-00634A
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the dryer belt, allowing it to rotate the drum during the drying cycle. Over time, the pulley wheel and its bearings can wear out leading to squ...Read moreeaking and grinding noises when the drum rotates. The bracket or pulley wheel can also fall out of alignment which can damage the belt and cause it to slip off. Eventually, a faulty idler pulley assembly will prevent the drum from rotating altogether. Depending on your dryer model, you may need to disassemble the dryer to access the pulley assembly. Remove the dryer belt from the idler pulley wheel and detach the assembly from the dryer frame. Position the new assembly in its place and secure it in position. Thread the belt over the pulley and around the dryer drum, ensuring that the grooved side lays flat against the drum. Manually spin the drum to check that the belt is properly tensioned and reassemble your appliance.
Read less
$28.30
On Order
Thermal Fuse
Part #DC47-00016A
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying cycle. A faulty thermostat could result in clothes getting burned because the heating element does not receive the necessary signal to stop ...Read moreproducing heat. This is a dangerous situation and could also lead to a fire. Ensure that you disconnect the power source to your dryer before you conduct this repair. This thermostat is connected to the clothes dryer unit by two screws which are sold separately.
Read less
$13.15
In Stock
Moisture Sensor
Part #DC61-02627A
This moisture sensor plate is specifically designed to fit with your Samsung dryer. It is made of stainless steel and measures approximately 5 inches long. It is designed to detect the amount of moisture in the clothes, and it sends signals to the control board when the clothes are dry so that the dryer can end the drying cycle. If your d...Read moreryer is not heating up properly or you find that your clothes are still damp at the end of the cycle, then the moisture plate sensor is likely malfunctioning.
Read less
$19.95
In Stock
Dryer Leveling Leg
Part #DC61-03128A
Leveling leg supports the dryer. Adjust the height of the leveling leg to make the dryer level.
$161.95
In Stock
$6.40
In Stock
Tapping Screw
Part #6002-000213
$50.75
In Stock
$13.15
In Stock
$101.44
In Stock
High Limit Thermostat - L230-50F
Part #DC47-00017A
$58.31
In Stock
Panel Air Seal (Front)
Part #DC62-00344A
This is a genuine OEM air seal designed for use with Samsung dryers. This seal ensures that air does not leak between the front panel and dryer drum. Over time and with gradual wear and tear, this air seal will age and become looser, resulting in tears, rips, and damage that will make it ineffective. If you notice longer drying times or c...Read morean feel a breeze when your Samsung dryer is in use, it needs to be replaced. To install it, ensure your dryer is turned off, and use protective gloves to protect your hands.
Read less
Common Symptoms of the DVG55CG7100VA3
How this model fails, and the parts that fix it.
Noisy
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More