Models
>
DV331AGWXAA
DV331AGWXAA Samsung Dryer - Overview
Sections of the DV331AGWXAA
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Drive Belt
PartSelect #: PS4133825
Manufacturer #: 6602-001655
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This ...
$44.87
In Stock
Thermistor
PartSelect #: PS4204984
Manufacturer #: DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of...
$35.53
In Stock
Idler Pulley Assembly
PartSelect #: PS11771601
Manufacturer #: DC93-00634A
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the ...
$62.67
In Stock
Thermal Fuse
PartSelect #: PS4205213
Manufacturer #: DC47-00016A
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying ...
$25.28
In Stock
Drum Support Roller & Axle
PartSelect #: PS4221885
Manufacturer #: DC97-16782A
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear ou...
$41.80
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$21.53
In Stock
Moisture Sensor
PartSelect #: PS4206812
Manufacturer #: DC61-02627A
This moisture sensor plate is specifically designed to fit with your Samsung dryer. It is made of stainless steel and measures approximately 5 inches long. It is designed to detect the amount of moist...
$19.29
In Stock
CASE-FILTER(U);BIG-BANG
PartSelect #: PS4206806
Manufacturer #: DC61-02610A
This lint screen case, or lint filter case is specially designed for Samsung dryers. It is responsible for securing the lint screen inside the lint screen housing and preventing it from falling out. T...
$45.69
In Stock
Leveling Leg
PartSelect #: PS4219720
Manufacturer #: DC97-12150A
The leveling leg on your dryer attaches to the bottom of the dryer base. The function of the leg is to keep your dryer level while it operates. This part is approximately 3 inches in length, 2 inches ...
$41.96
In Stock
Questions And Answers for DV331AGWXAA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Luigi
February 11, 2020
I have a Samsung dryer model number dv331agwxaa and it stop heating up. It runs through a cycle but doesn’t get hot. Just curious what you think it could be. It’s about 8 years old
For model number DV331AGWXAA
Hi Luigi,
Thank you for your question. If your dryer is not heating, there are some parts that you will need to check to see which one is causing the issue. You will need to check the coils, the heating element, the safety thermostat, the thermal fuse, the radiant flame sensor and the electronic control board. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the DV331AGWXAA
[Viewing 3 of 3]Noisy
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Parts Used:
-
Christopher from SUGARLOAF, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
23 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud noise like boots being ran through the dryer
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in th
... Read more
e front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Read less
Parts Used:
-
Tad from MINOT AFB, ND
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench set
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tension/Dead Man Wheel Broke/Shattered
Dryer would not start but electronics were working.
Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.
Ordered replacement wheel/arm.
One screw to remove ol ... Read more d one, one screw to install new one...tentioned the belt. Dryer was good as new.
Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.
Ordered replacement wheel/arm.
One screw to remove ol ... Read more d one, one screw to install new one...tentioned the belt. Dryer was good as new.
Read less
Parts Used:
-
Noah from OXFORD, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!