Models > DV210AESXAC

DV210AESXAC Samsung Dryer - Overview

Sections of the DV210AESXAC

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(6)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$19.99
  In Stock
Drive Belt – Part Number: 6602-001655
Drive Belt
★★★★★
★★★★★
(17)
PartSelect #: PS4133825
Manufacturer #: 6602-001655
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This ...
$43.33
  In Stock
Thermistor – Part Number: DC32-00007A
Thermistor
★★★★★
★★★★★
(16)
PartSelect #: PS4204984
Manufacturer #: DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of...
$27.18
  In Stock
Idler Pulley Assembly – Part Number: DC93-00634A
Idler Pulley Assembly
★★★★★
★★★★★
(22)
PartSelect #: PS11771601
Manufacturer #: DC93-00634A
$59.11
  In Stock
Thermal Fuse – Part Number: DC47-00016A
Thermal Fuse
★★★★★
★★★★★
(5)
PartSelect #: PS4205213
Manufacturer #: DC47-00016A
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying ...
$22.69
  In Stock
Heating Element - 5300W – Part Number: DC47-00019A
Heating Element - 5300W
★★★★★
★★★★★
(14)
PartSelect #: PS4205218
Manufacturer #: DC47-00019A
This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, ...
$151.51
  On Order
Thermal Fuse – Part Number: DC47-00015A
Thermal Fuse
★★★★★
★★★★★
(9)
PartSelect #: PS4205212
Manufacturer #: DC47-00015A
The thermal fuse measures the air temperature inside your dryer drum, and turns the heat on and off to maintain the optimal temperature during the drying cycle. If your dryer will not start, dry cloth...
$32.09
  In Stock
Drum Support Roller & Axle – Part Number: DC97-16782A
Drum Support Roller & Axle
★★★★★
★★★★★
(7)
PartSelect #: PS4221885
Manufacturer #: DC97-16782A
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear ou...
$40.68
  In Stock
Assembly DUCT HEATER;27-DRYE – Part Number: DC97-14486A
Assembly DUCT HEATER;27-DRYE
★★★★★
★★★★★
(21)
PartSelect #: PS4220205
Manufacturer #: DC97-14486A
$195.58
  In Stock
Moisture Sensor – Part Number: DC61-02627A
Moisture Sensor
★★★★★
★★★★★
(1)
PartSelect #: PS4206812
Manufacturer #: DC61-02627A
$12.02
  In Stock
High Limit Thermostat – Part Number: WP35001092
High Limit Thermostat
PartSelect #: PS11741822
Manufacturer #: WP35001092
This high limit thermostat controls the level of heat in a dryer to prevent overheating. It does this by measuring the temperature inside of the dryer drum and turns off when it reaches 260 degrees Fa...
$55.28
  In Stock
CASE-FILTER(U);BIG-BANG – Part Number: DC61-02610A
CASE-FILTER(U);BIG-BANG
★★★★★
★★★★★
(3)
PartSelect #: PS4206806
Manufacturer #: DC61-02610A
$17.81
  In Stock

Questions And Answers for DV210AESXAC

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the DV210AESXAC

[Viewing 5 of 5]
No heat or not enough heat
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Shuts off too soon
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Parts Used:
Drive Belt
  • Christopher from SUGARLOAF, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
15 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tension/Dead Man Wheel Broke/Shattered
Dryer would not start but electronics were working.

Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.

Ordered replacement wheel/arm.
One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new.
Parts Used:
Idler Pulley Assembly
  • Noah from OXFORD, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud noise like boots being ran through the dryer
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in the front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Parts Used:
Drum Support Roller & Axle
  • Tad from MINOT AFB, ND
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!