DSE26JSEDCSS General Electric Refrigerator - Parts

This is a replacement fill tube and grommet assembly for your refrigerator. This part acts your water line to your ice maker. If you’re noticing water in the back of the refrigerator or any kind of leak, or if your ice bucket isn’t filling up with as much ice, you may need to change out the fill tube and grommet assembly. When you purchas...Read moree this part, you get the water line, as well as the fill tube and grommet. This is an OEM part sourced directly from the manufacturer.

This motor is used to activate the blades to crush the ice for dispensing. This part is now threaded with a left hand thread and the J nut is no longer required.

This black freezer door gasket forms a tight seal around the door. It keeps cold air inside and blocks warm, damp air that can cause frost. Replace the gasket if it is torn, hard, loose, or badly bent. Before ordering, clean the seal and check the hinges, door frame, and gasket channel. Confirm fit with the full appliance model and the 37...Read more-by-31-inch size. Soak shipping folds in warm water for 5 to 10 minutes, press the gasket into place, smooth each side, and keep the door closed for several hours.

This is the replacement door handle for your refrigerator. It has a slightly curved shape, is chrome in color and is approximately 34 inches long and 2 inches wide. The door handle allows you to open and close your refrigerator door, and you will want to replace it if it is damaged or missing. This part is sold individually and is an OEM part sourced directly from the manufacturer.

This DC fan motor moves air across the condenser coils and compressor to help remove heat. A failed motor may cause poor cooling, a hot compressor, or humming and squealing sounds. Before replacing it, clean the coils and check the fan blade, wiring, and air path for dirt or damage. Confirm fit with the full appliance model, 4-pin plug, a...Read morend 11.3- to 12-volt rating. Unplug the refrigerator before removing the rear panel. Keep hands away from the blade, protect the cooling lines, and reinstall the panel before testing the unit.

This is the replacement bucket auger for your refrigerator. It is approximately 20 inches long and 14 inches wide. The bucket auger sits within the ice maker assembly and rotates to push the ice from the ice container into the dispenser chute. If your ice maker bucket is full, but ice is not being dispensed, it is an indication that the a...Read moreuger is damaged. Be sure to disconnect power from the refrigerator before you repair the auger. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

This part regulates the humidity of your crisper bins. It does so by opening and closing vents on the bin. If your humidity control is broken or missing, you will need to replace it. This is a genuine OEM part from GE and is sourced directly from the manufacturer.

This part is the replacement door stop for your refrigerator. It is made of black plastic and is approximately 2 inches by 1 ½ inches in size. The door stop attaches to the bottom of the door and prevents it from swinging open and hitting the refrigerator cabinet. If your door opens too far, or opens with little resistance, it could be an...Read more indication that you need to replace the door stop. You will also want to replace the door stop if it is cracked, broken, or missing. This part is sold individually and is an OEM part sourced directly from the manufacturer.

This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.

10-16 pl pnp 5/8 szn - Sold individually.

This part is the replacement fresh food door gasket for your refrigerator. It is made of black rubber and is sold individually. The fresh food door gasket runs along the circumference of your refrigerator’s fresh food door and creates the seal that allows your refrigerator to regulate the temperature inside. If the gasket is worn, stretch...Read moreed, or damaged, your fridge may become too warm, and you may notice the door is sweating. The door also may not open or close properly because of a damaged gasket. To replace the gasket, carefully pull the old gasket out the grooves it fits in around the door. Press the new gasket into the same grooves snugly. This part is an OEM part from the manufacturer.