EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

DE7600 Maytag Dryer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum Support Roller Kit – Part Number: 12001541
$22.52
In Stock
Drum Support Roller Kit
★★★★★
★★★★★
(200)
Part #12001541
The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft which is attached to the rear bulkhead. This part should be replaced whenever it does not rotate easily on the roller shaft. If you’re noticing a thump, scrape, or squeal while your drum is spinning, it may be your drum support rollers. Take a look at your existing drum rollers; if one or both of them are worn or broken, you’ll need to replace them. The drum support roller is subject to constant wearing when your dryer is in use, which causes them to break down over time. This part features 1 roller and 2 small washers, and measures approximately 3 inches in diameter. It is constructed with a combination of plastic, metal and rubber. This model comes in black/beige.
Tumbler and Motor Belt – Part Number: WPY312959
$26.82
In Stock
Tumbler and Motor Belt
★★★★★
★★★★★
(161)
Part #WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair. During the repair, make sure the belt doesn't fall into the groove in the drum, which will cause it to be too loose. You should be able to access the belt and replace it by removing the front panel and bulkhead.
Front Glide Kit – Part Number: 306508
$12.85
In Stock
Front Glide Kit
★★★★★
★★★★★
(44)
Part #306508
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulkhead removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this installation, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.
Roller Shaft – Part Number: WP6-3129480
No Longer Available
Roller Shaft
★★★★★
★★★★★
(4)
Part #WP6-3129480
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place for the roller to spin. The tools required for this repair are a stubby Phillips screwdriver, a 5/16 nut driver, a pair of snap ring pliers, and a 9/16 wrench. The first step before replacing this part should be to disconnect your dryer from the power source.
Blower Wheel with Clamp – Part Number: Y303836
$21.45
In Stock
Blower Wheel with Clamp
★★★★★
★★★★★
(112)
Part #Y303836
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses air through the drum and out of the exhaust vent. This part might need to be replaced if you notice your dryer is taking too long to dry clothing, it is not tumbling, or is making any unusually loud noises. The blower wheel measures about 7.5 inches in diameter by 3-3/8 wide. The blower wheel can be accessed by removing the front panel of your appliance.
Dryer Retaining Ring – Part Number: WP9703438
$6.40
In Stock
Dryer Retaining Ring
★★★★★
★★★★★
(3)
Part #WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter. The retaining ring is a genuine OEM part sourced directly from the manufacturer. The ring may vary in appearance due to manufacturer substitution, but the function is the same. You may need to replace this part if the dryer is noisy during tumbling, will not tumble, or takes too long to dry. Be sure to check drum support roller kit and shaft before ordering parts.
Lint Filter – Part Number: WP33002970
No Longer Available
Lint Filter
★★★★★
★★★★★
(67)
Part #WP33002970
This is a replacement lint filter for your dryer. Replacing this part is easy as it requires no disassembly of the unit. Make sure to clean the filter after every use of your dryer, and check the filter slot for excess lint buildup.
Drum Roller Shaft Washer – Part Number: WP312535
$12.85
In Stock
Drum Roller Shaft Washer
★★★★★
★★★★★
(1)
Part #WP312535
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold individually. It is located on the shaft of the drum roller, in the interior of your dryer. To access the drum roller shaft, you will need to remove the front panel of your dryer, and then remove the drum. Before completing this repair, be sure to disconnect the power source from the dryer. Tools required for this repair include a 5/16 nut driver, a stubby Phillips screwdriver, and a pair of snap ring pliers.
Idler Pulley Shaft Washer – Part Number: WPY312527
$12.85
In Stock
Idler Pulley Shaft Washer
Part #WPY312527
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
Idler Pulley Wheel – Part Number: WP6-3037050
$16.07
In Stock
Idler Pulley Wheel
★★★★★
★★★★★
(6)
Part #WP6-3037050
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
Door Switch Kit – Part Number: W10169313
$24.67
In Stock
Door Switch Kit
★★★★★
★★★★★
(20)
Part #W10169313
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble, replacing the door switch can solve this appliance problem. The tools needed for replacement are a screw driver and wire strippers. Make sure to attach the two wires to the right two poles of the new switch, to do this you can check the resistance of the switch. Unplug the dryer before installing this part, also refer to the diagram provided by the manufacturer.
Front or Rear Drum Felt Seal – Part Number: WP314820
$30.53
In Stock
Front or Rear Drum Felt Seal
★★★★★
★★★★★
(3)
Part #WP314820
This front or rear dryer drum felt seal is seventy-nine and a half inches long.

Questions And Answers for DE7600

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ivan - For model number DE7600
March 28, 2023
Where can I find a thermostat with 5 terminals.
Chris Boyle Profile
Hi Ivan, thank you for reaching out. The part you are looking for is the cycling thermostat, part number PS11740684. Good luck with the repair!
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Andrew - For model number DE7600
July 16, 2026
HelloOur tumbler makes noise as it spins.Wondering if it is the tumbler wheels or belt.And if so which parts I would need to fix it pleaseRegards
Chris Boyle Profile
Hi Andrew, thank you for contacting us. The issue could be with the drum rollers. The drum support roller for your model is part number PS1570070. You may need to replace it to fix the issue. We hope this sorts out your problem!
$22.52
In Stock
Drum Support Roller Kit
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Dave - For model number DE7600
December 7, 2023
Dyer gets very hot, the exhaust vent is clear of lint. The tub does turn by hand. When the turn dial is turned to any on position the dryer buzzer sounds non stop and starts getting warm but the tub does not spin. The only way to get the buzzer sound to stop is by opening the door.
Chris Boyle Profile
Hello Dave, thank you for contacting us. According to our research, the issue is most probably with the timer, part number PS11740662. It controls the electrical components and the duration of the dryer cycles. Glad to be of help!
$202.03
In Stock
Dryer Timer
Was this helpful?
Thank you for voting!
Gary - For model number DE7600
January 24, 2025
Do you have a heating element or can you get an element for this model?
Chris Boyle Profile
Hi Gary, Thank you for your question. The part number for the heating element is PS11740682. We hope this helps!
$176.37
In Stock
Heating Element - 240V
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the DE7600

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
noisy rollers, broken latch
673 of 705 people found this instruction helpful.
  • gerry from west covina,, CA
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable), Wrench set
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of t he front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Was this helpful?
Thank you for voting!
The blower fan (nylon) stripped off the motor shaft (steel)
574 of 583 people found this instruction helpful.
  • Stephen from Lafayette, IN
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Was this helpful?
Thank you for voting!
dryer squeeking
525 of 567 people found this instruction helpful.
  • gerald from park city, MT
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts.
Was this helpful?
Thank you for voting!