Models
>
DDT575SGF0BB
DDT575SGF0BB General Electric Dishwasher - Overview
Sections of the DDT575SGF0BB
[Viewing 6 of 6]
Manuals & Care Guides for DDT575SGF0BB
Click to downloadInstall
Installation Instructions
(0.25MB)
Install
Installation Instructions
(0.46MB)
Install
Installation Instructions
(7.30MB)
Install
Installation Instructions
(0.51MB)
Manual
Owner's Manuals
(20.04MB)
Keep searches simple, eg. "belt" or "pump".
LOWER RACK ROLLER
PartSelect #: PS16217024
Manufacturer #: WD12X26146
This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
$13.13
In Stock
Door Latch
PartSelect #: PS6447681
Manufacturer #: WD21X10490
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
$44.23
In Stock
Dishwasher Tub Gasket
PartSelect #: PS11774412
Manufacturer #: WD08X23476
The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the...
$21.59
In Stock
Flood Switch
PartSelect #: PS8690623
Manufacturer #: WD21X10519
This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
$53.93
In Stock
LOWER SPRAY ARM ASSEMBLY
PartSelect #: PS16542476
Manufacturer #: WD22X27724
This lower spray arm assembly in your dishwasher distributes water and detergent during the washing cycle by spinning around and spraying water in different directions. You can usually find it attache...
No Longer Available
HEATING ELEMENT
PartSelect #: PS16729156
Manufacturer #: WD05X30818
The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cy...
$56.26
In Stock
Countertop Bracket
PartSelect #: PS11700868
Manufacturer #: WD01X21740
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
$7.49
In Stock
Upper Rack Assembly
PartSelect #: PS16618975
Manufacturer #: WD28X30219
This dishrack is for dishwashers. The dishrack holds the dishes in place during the dishwashing cycle. Follow the instructions in the manual when installing this part.
$82.29
In Stock
Screw 8-16 hxw 1/2 Stainless Steel
PartSelect #: PS258461
Manufacturer #: WD02X10067
Sold Individually.
$8.54
In Stock
Rack Carrier Kit - Right or Left side
PartSelect #: PS16219735
Manufacturer #: WD28X27241
This part is the replacement carrier roller for your dishwasher. It is also known as the wheel support. It is made of gray plastic and is approximately 5 inches by 2 inches. The carrier roller support...
$14.71
In Stock
Leveling Screw
PartSelect #: PS11762951
Manufacturer #: WD12X23057
This is a genuine GE dishwasher leveling screw. It operates as a leg on the bottom of your dishwasher, and can be screwed in and out to raise and lower the height of the dishwasher. It is made of meta...
$8.06
In Stock
Upper Spray Arm
PartSelect #: PS11729217
Manufacturer #: WD35X20794
This part is the upper spray arm for your dishwasher. The spray arm is made of plastic and is approximately 10 inches wide. The upper spray arm is mounted to the top of the dishwasher tub, and rotates...
$33.92
On Order
Questions And Answers for DDT575SGF0BB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DDT575SGF0BB
[Viewing 9 of 9]Leaking
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No water flowing into dishwasher
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve.
... Read more
I extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
Read less
Parts Used:
-
Jeff from AUBURNDALE, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
32 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was leaking from the bottom of the door during wash cycle
I replaced the tub gasket around the door circumference which took less than five minutes to replace. However the problem was replacing the beach gasket that prevents the water from flowing out of the dishwasher tub. The door had to be unhinged from the dishwasher which was unscrewed from the cabinets and brought out from its location. Af
... Read more
ter the door was completely removed it was laid on its front. After removing the door hinges which were secured with just one bolt I tried to slide the back panel off the front panel but without any success. So I had to remove the torn and worn out gasket while working in a tight space. This is where the problem rose because according to installation instructions there are screws supposed to be holding it to the main body frame. However, in my case rivets were used by the manufacture since this was the first time the gasket was being replaced. So I had to use a power tool With a grinding bit to remove the face of the rivets and essentially cut them out to reveal the underlying holes. After this I replace the beach gasket and then used half inch SS Philips bolts and nuts to secure the gasket to the body frame.
Read less
Parts Used:
-
Mohammad from WOODBRIDGE, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
27 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch not functioning
1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. ... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. ... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
Read less
Parts Used:
-
James from ALBRIGHTSVLLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
24 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!