Switch to Classic
2 questions answered by our experts.
Models
>
DCVH515EF0WW
DCVH515EF0WW General Electric Dryer - Overview
Sections of the DCVH515EF0WW
[Viewing 7 of 7]
Manuals & Care Guides for DCVH515EF0WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Drum Bearing Slide - White
In Stock
PartSelect #: PS755842
Manufacturer #: WE1M504
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
$11.79
Drum Bearing Slide - Green
In Stock
PartSelect #: PS6447706
Manufacturer #: WE1M1067
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
$8.90
Duct Felt Seal
In Stock
PartSelect #: PS9861764
Manufacturer #: WE09X20441
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
$9.69
BELT DRIVE
In Stock
PartSelect #: PS16542496
Manufacturer #: WE03X29897
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
$41.83
Rear Drum Bearing Kit
In Stock
PartSelect #: PS267529
Manufacturer #: WE25M40
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
$78.51
Light Bulb
In Stock
PartSelect #: PS10063224
Manufacturer #: WE05X20431
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
$15.16
Top Bearing
In Stock
PartSelect #: PS1766010
Manufacturer #: WE14M124
The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
$74.17
Idler Pulley Wheel
In Stock
PartSelect #: PS265721
Manufacturer #: WE12X83
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
$33.42
Door Latch
In Stock
PartSelect #: PS3502777
Manufacturer #: WE1M1011
This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on ...
$8.67
Interlock Switch
In Stock
PartSelect #: PS1481922
Manufacturer #: WD21X10261
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. ...
$20.16
Questions And Answers for DCVH515EF0WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
August 26, 2021
The top of the drum is trapping items between the drum and frame, causing the items to remain snagged as the drum continues to turn, usually just twisting and leaving marks, but also tearing some holes in clothes.What to do?
For model number DCVH515EF0WW
Hello Brian, Thank you for your inquiry. We have researched your model and recommend the following parts to fix your issue: top bearing, the dryer drum glides, the drum seal felt seal and the duct trap assembly. Also check the belt to make sure the drum is rotating properly and not out of place. Hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
Linda
November 30, 2021
Dryer will turn on and run a few minutes and shut off. Have to unplug and wait a few minutes and it will turn back on and run a few minutes and shut off again. It does this in all modes (at least the few i tried)
For model number DCVH515EF0WW
Hello Linda, thank you for writing. There are a few options with this issue. First, please take off the back of the dryer and thoroughly vacuum the inside and inside the vent tubing. Second, it may be a faulty Door Latch PartSelect Number PS3502777 or Door Switch PartSelect Number PS2344321 that the motion of the laundry is popping the door open. If the Moisture Sensor PartSelect Number PS1021860 is defective or dirty, it may fail to detect moisture and inadvertently tell the dryer to shut off when the laundry is still wet. Good luck with your repair.
Was this helpful?
Thank you for voting!
Common Symptoms of the DCVH515EF0WW
[Viewing 11 of 11]Noisy
Fixed by
these parts
these parts
Show All
Will not tumble
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
No heat or not enough heat
Fixed by
these parts
these parts
Show All
Takes too long to dry
Fixed by
these parts
these parts
Show All
Shuts off too soon
Fixed by
these parts
these parts
Show All
Will not shut off
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Parts Used:
-
Matthew from Plainfield, IL -
Difficulty Level:Really Easy -
Total Repair Time:15 - 30 mins -
Tools:Screw drivers
755 of 853 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LOUD - screeching noise during drying cycle, in all modes of operation.
1. Removed top cap on lid by removing the 3 - phillips screws.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.
6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.
6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Parts Used:
-
Bruce from Springfield, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
238 of 325 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heater element went out
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.
Remove the element disc from the rear of the housing, take note of the the wireing placement. Replace disc and reverse order of disassembly.
This job was easy for me as I am a tinkerer by nature. The hardest part of the whole job was waiting on the part, which by the way was ordered on a Sunday evening and I had the replacement in my hands and back in the dryer running by 1:00 PM on the following Tuesday!
I book marked this website and WILL refer it to others who simply need a repair, not a costly new appliance!
Remove the element disc from the rear of the housing, take note of the the wireing placement. Replace disc and reverse order of disassembly.
This job was easy for me as I am a tinkerer by nature. The hardest part of the whole job was waiting on the part, which by the way was ordered on a Sunday evening and I had the replacement in my hands and back in the dryer running by 1:00 PM on the following Tuesday!
I book marked this website and WILL refer it to others who simply need a repair, not a costly new appliance!
Parts Used:
-
Brian from Clinton, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
174 of 208 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
