D28715X (Type 2) DeWALT Chop Saw - Overview

This M8 × 1.25 elastic stop nut (lock nut) is an OEM replacement fastener used on power tools to securely hold critical components in place while resisting loosening from vibration. Designed with an integrated nylon insert, it provides reliable locking force without the need for additional hardware and is ideal for replacing worn or missing nuts during maintenance or repair to ensure safe, stable operation.

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

This is a genuine OEM approved replacement part designed for use with chop saws. This item holds carbon brush against the armature. It is made out of plastic with metal and it is sold individually. Please note carbon brushes are sold separately. To replace this assembly you would need a screwdriver and pliers. • First remove screws ho...Read morelding the cover together • Carefully remove two halves of the housing to gain access to armature and brush holder • Remove the screws holding brush holder to the trigger • Remove the armature assembly and the brush holder • Install the new brush holder, brushes and the armature • Reassemble and test your tool

Help restore reliable motor performance with this carbon brush, designed to maintain electrical contact between the motor's stationary and rotating components. As brushes wear naturally over time, replacing a worn brush can help resolve issues such as power loss, excessive sparking, intermittent operation, or motor failure. This replaceme...Read morent brush helps ensure efficient power transfer and consistent tool performance. Because most compatible tools use two brushes, replacing both at the same time is recommended for balanced wear and optimum operation. Refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

This screw is commonly used on a variety of power tools. It is a genuine OEM sourced replacement part. Please make sure to check appropriate diagrams for correct location and use of this screw. Includes one pan head screw per order. You will need a screwdriver to install or remove it.

This item has been sourced from the original manufacturer to ensure a high level of quality. The identification label is intended to be used with miter saws from DeWalt. The adhesive label attaches to the motor case endcap. Replacing the label is a good way to improve the look of a used or refurbished miter saw. This item is sold as an individual replacement.

This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on t...Read morehe tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a DeWALT replacement part directly sourced from the manufacturer for use in saws. The clamp washer goes between the blade adapter and the blade clamp. A screwdriver might be needed during the installation process. It is made of metal and will require replacing if it becomes broken. This is available as an individual replacement part but keep in mind that two may be needed.

This cord guard is a genuine DeWalt replacement part and is sold individually. • Cord guards, also called cord protectors, are designed to slide onto and fit securely at the end of your cord, where its firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. ...Read more • This cord guard will fit cords for the tools listed under the "Compatible Tools" listing. It is not guaranteed to fit any other cords.

Genuine OEM replacement part, this item is sold individually. This screw is used in various places in all of the tools listed below The most common use for this screw is to secure plastic housings together. It has a Torx T-20 head.