D26451-AR (Type 1) DeWALT Sander Polisher - Overview

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on th...Read moree Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Genuine Dewalt replacement part, this item is sold individually. The purpose of the 624302-00 Brake is to keep the sanding pad of the Random Orbit Sander at a slower speed so that the sander can sand the stock properly. A good time to replace the Brake is when you replace the sanding pad. Or replace it when the pad is spinning out of control at high RPM.

This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.

Genuine OEM replacement part designed for certain Random Orbit Sanders. This item is made out of Metal and it is Sold Individually. This is the bottom Bearing Retainer that keeps the bearing in place. It is attached to the fan with 3 screws which are Sold Separately.

It is a high-quality OEM part that is specially made for Porter Cable, Black and Decker and DeWALT power tools. The receptacle is designed to safely secure and connect a wire. It is an identical replacement for a faulty or a missing part that was installed on a new unit. To ensure the correct application, refer to the appropriate diagrams...Read more of your model. Note, this high-quality receptacle is made of durable metal and is sold individually. You will need a screwdriver to take the housing apart when replacing this component.

This is a genuine Dewalt replacement part, it is sold individually. The 151442-02 is part of the brake system for the Random Orbit Sanders listed below. They connect to the 624302-00 Brake to help it keep the sanding pad at a slower orbit so it works properly.

This authentic item is supplied by the original manufacturer for DeWALT random orbit sanders. It is the bottom half of the bearing retainer which is utilized to secure the armature bearing. The part is secured three screws which also attach the sanding pad. Note, the hardware is sold separately. It provides a high-quality replacement for ...Read morea missing or a damaged part that was installed on a new unit. Make sure to refer to the owner's manual and the diagrams of your model for the correct installation of this component. You will need a screwdriver to perform this repair.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-ring failure. The most common among power tools are: • The O-ring has ragged, tattered edges. These are commonly caused by pressure ...Read morespikes which shear off tiny "bites" from the O-ring, or caused by clearance gaps. • One or both sides of the O-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit, or is too smooth to allow lubrication. • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding O-ring capacity. • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays, and air pollution. Excessive seal stretching (greater than 5%) causes similar cracking.

This genuine cord protector, also known as a strain relief boot, is designed to safeguard the power cord where it enters your tool housing. Made from flexible, durable material, it helps prevent the cord from bending, twisting, or fraying during regular use, supporting safe and reliable performance. Small but essential, this component is ...Read morean effective replacement if the original protector is worn or damaged, helping extend the life of your tool and maintain proper cord alignment.